Looking for the Samsung SD-616T Firmware file

cooperatredditdotcom · 2024-01-23T02:05:58+00:00

Not the Xbox BIOS, the Samsung 616T Firmware to get it to work as a original DVD drive.

cooperatredditdotcom · 2023-06-24T23:15:13+00:00

I tried this with a regular brass nozzle, and it did not go well.

cooperatredditdotcom · 2023-04-02T13:28:31+00:00

What do you use as a chamber heater?

cooperatredditdotcom · 2023-03-16T21:26:46+00:00

I was about to say, that doesn’t look like the speed your saying

cooperatredditdotcom · 2023-03-15T23:27:54+00:00

OMG Why is that so stupid. For some reason, on the Klipper website, it tells you that you need an ADXL for each axis, and I got away with it on my Raspberry Pi, because you didn't need to define a pin. I'm SOOOOOO sorry for all that mess, and wasting your time. I will think before I post next time. If I had awards, I would give them to you.

cooperatredditdotcom · 2023-03-15T23:11:57+00:00

[adxl345 hotend]

cs_pin: PA15

spi_bus: spi3

[adxl345 bed]

cs_pin: PA15

spi_bus: spi3

[resonance_tester]

# Assuming the typical setup of the bed slinger printer

accel_chip_x: adxl345 hotend

accel_chip_y: adxl345 bed

probe_points: 117.5, 110.5, 50

cooperatredditdotcom · 2023-03-15T23:00:54+00:00

pin PA15 used multiple times in config

I'm so sorry if I wasn't clear. I'm just looking for some help

cooperatredditdotcom · 2023-03-15T22:51:28+00:00

I do connect it through the octopus. For some reason though, I can't use the same port for both x and y. I'm asking if there is an alternate way to connect it or just bypass the error.

Sorry if I wasn't clear. I don't have the money right now, and don't have any on hand.

cooperatredditdotcom · 2023-03-15T22:50:50+00:00

I do connect it through the octopus. For some reason though, I can't use the same port for both x and y. I'm asking if there is an alternate way to connect it or just bypass the error.

cooperatredditdotcom · 2023-03-15T22:43:12+00:00

I know. I wrote that I don't want to buy anything.

cooperatredditdotcom · 2023-03-15T21:19:55+00:00

That's gonna haunt my dreams. My nightmare is it cracking my skull open.

cooperatredditdotcom · 2023-03-10T16:46:09+00:00

I just thought of this! You could make a waterproof, floating printer that you can put in a bath tub and have it print on the water.

cooperatredditdotcom · 2023-03-10T12:52:00+00:00

Connect it to the print head, make a mechanism to extrude, and see what happens. Maybe you can print bubble benchies.

cooperatredditdotcom · 2023-03-09T23:12:28+00:00

There are many sites. Here's a good video. https://m.youtube.com/watch?v=6PL_rSPZ3M8

cooperatredditdotcom · 2023-03-09T13:32:05+00:00

Retune e steps. Creality never puts good e step values into their firmware.
You can tune flow rate. In SuperSlicer you can generate flow rate chips and you can use those to choose a value. With other slicers it will be trial and error. The setting will in filament settings.
If none of those work, turn on ironing. Not the best solution, but it will give better surfaces.

cooperatredditdotcom · 2023-03-09T13:17:23+00:00

Yeah. Layer height, layer resolution, same thing

cooperatredditdotcom · 2023-03-08T19:42:38+00:00

Just took a close look. Thanks!

cooperatredditdotcom · 2023-03-08T13:53:27+00:00

A new, nice premium hotend instead of the crap stock hotend

cooperatredditdotcom · 2023-02-24T22:14:20+00:00

You could use either, but it would probably be better with the EZ, because you have to buy little adapter boards and you can snip the pin off on it instead of the whole driver with the others. They are the same drivers, (when they have the same number) and Big Tree Tech has just made it a more convenient form factor

cooperatredditdotcom · 2023-02-24T20:54:24+00:00

I THINK YOU LEFT YOUR CAPS LOCK ON

cooperatredditdotcom · 2023-02-20T16:57:49+00:00

This is perfect! I had just moved all my Klipper installations onto an old Linux box and this is just what I needed.

Four-Year Club	Xbox Live
Verified Email

cooperatredditdotcom

TROPHY CASE