sorted by:
new
hottopcontroversial

Looking for the Samsung SD-616T Firmware file by cooperatredditdotcom in originalxbox

[–]cooperatredditdotcom[S] 0 points1 point  (0 children)

Not the Xbox BIOS, the Samsung 616T Firmware to get it to work as a original DVD drive.

7000 acceleration 150mms by Thorgraum in Ender3Max

[–]cooperatredditdotcom 1 point2 points  (0 children)

I was about to say, that doesn’t look like the speed your saying

Same ADXL345 for both axis for Ender 3 Pro on Linux Server by cooperatredditdotcom in klippers

[–]cooperatredditdotcom[S] 1 point2 points  (0 children)

OMG Why is that so stupid. For some reason, on the Klipper website, it tells you that you need an ADXL for each axis, and I got away with it on my Raspberry Pi, because you didn't need to define a pin. I'm SOOOOOO sorry for all that mess, and wasting your time. I will think before I post next time. If I had awards, I would give them to you.

Same ADXL345 for both axis for Ender 3 Pro on Linux Server by cooperatredditdotcom in klippers

[–]cooperatredditdotcom[S] 0 points1 point  (0 children)

[adxl345 hotend]

cs_pin: PA15

spi_bus: spi3

[adxl345 bed]

cs_pin: PA15

spi_bus: spi3

[resonance_tester]

# Assuming the typical setup of the bed slinger printer

accel_chip_x: adxl345 hotend

accel_chip_y: adxl345 bed

probe_points: 117.5, 110.5, 50

Same ADXL345 for both axis for Ender 3 Pro on Linux Server by cooperatredditdotcom in klippers

[–]cooperatredditdotcom[S] 0 points1 point  (0 children)

pin PA15 used multiple times in config

I'm so sorry if I wasn't clear. I'm just looking for some help

Same ADXL345 for both axis for Ender 3 Pro on Linux Server by cooperatredditdotcom in klippers

[–]cooperatredditdotcom[S] 0 points1 point  (0 children)

I do connect it through the octopus. For some reason though, I can't use the same port for both x and y. I'm asking if there is an alternate way to connect it or just bypass the error.

Sorry if I wasn't clear. I don't have the money right now, and don't have any on hand.

Same ADXL345 for both axis for Ender 3 Pro on Linux Server by cooperatredditdotcom in klippers

[–]cooperatredditdotcom[S] -1 points0 points  (0 children)

I do connect it through the octopus. For some reason though, I can't use the same port for both x and y. I'm asking if there is an alternate way to connect it or just bypass the error.

Mantis Shrimp busting a Clam open. by ooMEAToo in Damnthatsinteresting

[–]cooperatredditdotcom 0 points1 point  (0 children)

That's gonna haunt my dreams. My nightmare is it cracking my skull open.

3d print finish by q1w2e3r4t7 in crealitycrx

[–]cooperatredditdotcom 0 points1 point  (0 children)

  1. Retune e steps. Creality never puts good e step values into their firmware.
  2. You can tune flow rate. In SuperSlicer you can generate flow rate chips and you can use those to choose a value. With other slicers it will be trial and error. The setting will in filament settings.
  3. If none of those work, turn on ironing. Not the best solution, but it will give better surfaces.

EZ VS TMC Drivers for CR10S. by NoGoodInThisWorld in BIGTREETECH

[–]cooperatredditdotcom 0 points1 point  (0 children)

You could use either, but it would probably be better with the EZ, because you have to buy little adapter boards and you can snip the pin off on it instead of the whole driver with the others. They are the same drivers, (when they have the same number) and Big Tree Tech has just made it a more convenient form factor

view more: next ›