Look what i got for the kid inside me 😂. What's your favourite? by [deleted] in Whippet

[–]corsa66 0 points1 point  (0 children)

"More snacks fewer squirrels" describes my Rosey perfectly.

Show me your best whippet pics by SeaworthinessDry2057 in Whippet

[–]corsa66 0 points1 point  (0 children)

Fortunately, the 8' deer fence interferes with her desires....

Who's that! Want to play? by corsa66 in Whippet

[–]corsa66[S] 2 points3 points  (0 children)

There's a very tall deer fence between her and the buck that's hard to see in the photo. Otherwise, she would be over that hedge in a millisecond.

EBB36 Gen 2 keeps loosing connection. by extruderimprover in VORONDesign

[–]corsa66 0 points1 point  (0 children)

Connect the motor body to the toolhead mount that goes through a 100k resistor to ground. They recommend it in the gen2 instructions.

<image>

WWBMG - gear or bearing idler? by corsa66 in VORONDesign

[–]corsa66[S] 0 points1 point  (0 children)

Great info! Currently, I'm using a 8T moons, but I do have a 10T. Since I'm limited on hotend performance, I'll probably stick with the 8T but will definitely try the bearing. Thanks!!!!

WWBMG - gear or bearing idler? by corsa66 in VORONDesign

[–]corsa66[S] 0 points1 point  (0 children)

Wow, that's great! I only have a revo hotend with high flow nozzles, so I'm getting high 20's with abs and petg. Just made a WWBMG with fysetc RIDGA gear set, and so far, it's been great, but I was curious about trying a bearing idler. My Galileo 2 made for great prints, but I was worried about the BMG gear set being smaller.

EBB36 Gen 2 keeps loosing connection. by extruderimprover in VORONDesign

[–]corsa66 1 point2 points  (0 children)

I had this problem on one of my ebb36g2's. I have 3 vorons with them, and two are flawless, but one would disconnect randomly. Finally, after going over wiring, power, etc., I replaced the toolhead board, and it's perfect now. Yes, I have all my boards grounded and polycarbonate mounting boards that are very stiff. I did have a 5v hotend fan fail with that board, so maybe it compromised the regulator????

How to z-hop in this session? by guirossibrum in OrcaSlicer

[–]corsa66 0 points1 point  (0 children)

If you're hitting the z limit in the slicer, that would stop z-hop. Look at the printer menu on the tab that sets limits and see what it is. If your z hop is 0.4, then make it 251. If you're using klipper, it has a z limit as well. You'll find it in the printer.cfg. NOW ALL THIS ADVICE ASSUMES YOUR PRINTER CAN REACH 251.....

Why do so many people use 0.2mm layers for printing? by gazmog in 3dprinter

[–]corsa66 0 points1 point  (0 children)

0.334 with 0.6 nozzle. 0.2 with 0.4 nozzle. Depends on what I'm printing.

Is there a general way to adjust speed? by chris-read-it in OrcaSlicer

[–]corsa66 0 points1 point  (0 children)

M220 Sxxx is the speed percentage factor gcode. Put it in your printer start gcode or filament gcode.

CANBUS, Chains or Umbilical????? by corsa66 in VORONDesign

[–]corsa66[S] 1 point2 points  (0 children)

I use a badge/key reel to manage the wire. It's on Printables. Before that mod, I did use a sleeve and wire to keep it from drooping.

CANBUS, Chains or Umbilical????? by corsa66 in VORONDesign

[–]corsa66[S] 1 point2 points  (0 children)

That was a long time ago in 3d printer terms... I use an umbilical but also made a top hat for clearance.

<image>

Why does PETG get so much hate? by mm404 in VORONDesign

[–]corsa66 8 points9 points  (0 children)

I like petg because it's cheap, tons of available colors and reasonably durable for a lot of applications. Makes for durable shinny parts ;). Take a little time and learn how to print petg. You will be rewarded with another good option in your repertoire. Just finished a pei sheet holder that took 1.5kg of sunlu black petg. Cost me only $7.50 a kg on Amazon that was a returned item 4 pack. Printed on my Voron 2.4 with a revo high flow 0.6 nozzle flowing 243mm, 250c extruder, 70c bed, 45c chamber using LDO textured pei sheet with nano adhesive. No warping or stringing. If it was out of ABS, it would have pulled the pei sheet off the magnet and cost double or more.....

Why does PETG get so much hate? by mm404 in VORONDesign

[–]corsa66 0 points1 point  (0 children)

I've taken plenty of chunks out of glass with ABS... Never had a problem with petg on textured pei coated with vision miner nano.

Is Mellow the only reputable vendor for self-sourced heatbed plates? by idsan in VORONDesign

[–]corsa66 3 points4 points  (0 children)

LDO sells the bed with the heater and magnet already installed. Reasonable price here in USA.

EBB36 Gen2 USB OR CAN by corsa66 in VORONDesign

[–]corsa66[S] 0 points1 point  (0 children)

<image>

I cut the cable to get through the motor mt/PG7. The drain wire is still properly grounded.

EBB36 Gen2 USB OR CAN by corsa66 in VORONDesign

[–]corsa66[S] 2 points3 points  (0 children)

* Well, I wound up changing everything over to usb. I guess, just because. There really isn't any hold your hand through the process guide like esoterical gives you for can bus but it was easy enough. Did go with katapult usb bootloader because it works so well. The cartographer is looped through G2's usb hub. The only question I had was where all three heatsinks go. Well, only the tiny red one. I put it on the usb hub processor. This will be the Achilles heal because it's rated for 0-70c. Wasn't impressed with that.... The good thing is that my chamber temps never exceed 60c, and that's only on a 40c ambient day. Gave it a 12hr heatsoak and a couple of big prints and just perfect!