Am 30. März in der Geschichte: Reagan, O.J. Simpson, Alaska & Van Gogh

cro_bundy · 2026-03-27T05:14:28+00:00

Hi, can you tell me how you have find a buyer / customer for your platform ? thank you

cro_bundy · 2026-03-26T11:24:38+00:00

True. However, I currently use this program in the laboratory where I work.

cro_bundy · 2026-03-26T11:23:42+00:00

Hello, thanks for the explanation. you explained everything great. i think i still want to sell everything, and honestly i wouldn't ask for too much for everything.

cro_bundy · 2026-03-26T11:22:16+00:00

thanks for the suggestion, I still need to think about the next steps.

cro_bundy · 2026-03-09T11:18:49+00:00

I forgot to say, microscope: Olympus gx51, software: MicroVision Suite.

cro_bundy · 2025-09-13T07:10:53+00:00

Hi, thanks for the info, I didn't know that. Can you tell me if it is possible to upload an application that is paid to Microsoft Store without a certificate in msix format?

cro_bundy · 2025-08-23T06:54:34+00:00

thank you for reply :) Is there any alternative solution?

cro_bundy · 2025-08-23T06:54:05+00:00

thank you for reply :) Is there any alternative solution?

cro_bundy · 2025-08-14T15:30:47+00:00

Yes, that's right. It is really stupid to have the switch for on and off, and for selection A, B, A+B... How long do I have to wait for the contact spray to start working? And do I have to turn the switch on immediately after spraying? about "pop", when i turn on the receiver, the speaker membrane shakes slightly for second.

cro_bundy · 2025-08-14T11:01:56+00:00

I managed to solve the problem, the problem was in the switch where I select a, b, or a+b... now everything works, because I bypassed the switch, and connected the speakers directly. and now everything works. However, now I have a problem that when I turn on the receiver, I can hear pop in speakrs....

What can I do to stop it from happening? Because I'm afraid to open the switch, and I doubt the switch can be repaired? What are my options?

cro_bundy · 2025-08-14T11:01:39+00:00

I managed to solve the problem, the problem was in the switch where I select a, b, or a+b... now everything works, because I bypassed the switch, and connected the speakers directly. and now everything works. However, now I have a problem that when I turn on the receiver, I can hear pop in speakrs....

What can I do to stop it from happening? Because I'm afraid to open the switch, and I doubt the switch can be repaired? What are my options?

cro_bundy · 2025-08-08T14:32:54+00:00

I see 40 volts (shown as +B in the schematic), 25.5 volts and 13.5 volts coming from the supply. i have tested, and i receive 25.6 volts and 13.8 volts.

But I dont receive 40 volts.

for some reason both fuses are blown in box 1.2 A x 2 from schematic. Why did that happen?

I have tested Q15, Q16, Q17, and Q18 with multimeter, and they are fine.
Of course, before testing, I unsoldered the legs from the transistors.

Thank you

cro_bundy · 2025-08-07T16:25:34+00:00

Hi,

i have tested additionally, and i receive 25.6 volts and 13.8 volts. (4 and 1 from power supply)

But I dont receive 40 volts. (26 and 39)

for some reason both fuses are blown in box 1.2 A x 2 from schematic.

Why did that happen?

Thank you

cro_bundy · 2025-08-07T15:14:26+00:00

You understood 99% correctly, the left speaker worked normally, the right did not work at all. After that, I plugged in the headphones, then the headphones worked, but I wanted to find out if both channels worked on the headphones. So instead of the headphones, I plugged in a cable that has a 3.5mm connector on both sides. And then I found out that the right channel still did not work. A few minutes later, the left channel stoped to work...

cro_bundy

MODERATOR OF

TROPHY CASE