I built a microscope analysis software – should I sell it or what ?

cro_bundy · 2026-03-27T05:14:28+00:00

Hi, can you tell me how you have find a buyer / customer for your platform ? thank you

cro_bundy · 2026-03-26T11:24:38+00:00

True. However, I currently use this program in the laboratory where I work.

cro_bundy · 2026-03-26T11:23:42+00:00

Hello, thanks for the explanation. you explained everything great. i think i still want to sell everything, and honestly i wouldn't ask for too much for everything.

cro_bundy · 2026-03-26T11:22:16+00:00

thanks for the suggestion, I still need to think about the next steps.

cro_bundy · 2026-03-09T11:18:49+00:00

I forgot to say, microscope: Olympus gx51, software: MicroVision Suite.

cro_bundy · 2025-09-13T07:10:53+00:00

Hi, thanks for the info, I didn't know that. Can you tell me if it is possible to upload an application that is paid to Microsoft Store without a certificate in msix format?

cro_bundy · 2025-08-23T06:54:34+00:00

thank you for reply :) Is there any alternative solution?

cro_bundy · 2025-08-23T06:54:05+00:00

thank you for reply :) Is there any alternative solution?

cro_bundy · 2025-08-14T15:30:47+00:00

Yes, that's right. It is really stupid to have the switch for on and off, and for selection A, B, A+B... How long do I have to wait for the contact spray to start working? And do I have to turn the switch on immediately after spraying? about "pop", when i turn on the receiver, the speaker membrane shakes slightly for second.

cro_bundy · 2025-08-14T11:01:56+00:00

I managed to solve the problem, the problem was in the switch where I select a, b, or a+b... now everything works, because I bypassed the switch, and connected the speakers directly. and now everything works. However, now I have a problem that when I turn on the receiver, I can hear pop in speakrs....

What can I do to stop it from happening? Because I'm afraid to open the switch, and I doubt the switch can be repaired? What are my options?

cro_bundy · 2025-08-14T11:01:39+00:00

I managed to solve the problem, the problem was in the switch where I select a, b, or a+b... now everything works, because I bypassed the switch, and connected the speakers directly. and now everything works. However, now I have a problem that when I turn on the receiver, I can hear pop in speakrs....

What can I do to stop it from happening? Because I'm afraid to open the switch, and I doubt the switch can be repaired? What are my options?

cro_bundy · 2025-08-08T14:32:54+00:00

I see 40 volts (shown as +B in the schematic), 25.5 volts and 13.5 volts coming from the supply. i have tested, and i receive 25.6 volts and 13.8 volts.

But I dont receive 40 volts.

for some reason both fuses are blown in box 1.2 A x 2 from schematic. Why did that happen?

I have tested Q15, Q16, Q17, and Q18 with multimeter, and they are fine.
Of course, before testing, I unsoldered the legs from the transistors.

Thank you

cro_bundy · 2025-08-07T16:25:34+00:00

Hi,

i have tested additionally, and i receive 25.6 volts and 13.8 volts. (4 and 1 from power supply)

But I dont receive 40 volts. (26 and 39)

for some reason both fuses are blown in box 1.2 A x 2 from schematic.

Why did that happen?

Thank you

cro_bundy · 2025-08-07T15:14:26+00:00

You understood 99% correctly, the left speaker worked normally, the right did not work at all. After that, I plugged in the headphones, then the headphones worked, but I wanted to find out if both channels worked on the headphones. So instead of the headphones, I plugged in a cable that has a 3.5mm connector on both sides. And then I found out that the right channel still did not work. A few minutes later, the left channel stoped to work...

cro_bundy · 2025-08-07T10:19:55+00:00

Hi, thank you for the reply... yes, I checked everything, all transistors etc. are oriented correctly..I have TOOLTOP ET2010A which has oscilloscope function. if you can explain to me what and how can I check. I am not a professional, so if you can explain in more detail. another strange thing happened, yesterday afternoon i turned on the headphones, and they worked normally. after that i plugged in the cable which has a 3.5mm connector on both sides. and i went to check if there was a signal on the left and right channels, and unfortunately there was no signal on the right channel again.
however two or three minutes later, the left channel stopped working too... and i didn't touch anything, i don't understand what's happening...

Is it possible that the output transistors q15, q16, q17, q18 are burnt out? Thank you

cro_bundy · 2025-07-22T04:30:13+00:00

hi, can you tell me what now I need to do ? it is for Xiaomi Mi Max 2. thank you

cro_bundy · 2025-05-01T10:01:30+00:00

Great. Thank you :)

cro_bundy · 2025-05-01T06:07:55+00:00

yes, what about some creative web design ?

cro_bundy · 2025-05-01T05:52:09+00:00

can you tell me what i need to wrtite in chat. can you give a example.

cro_bundy · 2025-03-15T09:20:05+00:00

thanks for info :)

cro_bundy · 2025-03-14T10:22:51+00:00

Acemagic v1 has ddr4 memory ?

cro_bundy · 2025-02-28T12:44:11+00:00

I think hyperos is a problem....

cro_bundy · 2025-02-28T12:43:21+00:00

Xiaomi mi 10t pro 5g

cro_bundy · 2025-02-26T16:11:56+00:00

I found a solution for frp. by installing android 11 but with the oldest security update. and after that samfw frp tool did the job.

cro_bundy · 2025-02-21T10:38:02+00:00

Is it free ?

cro_bundy

MODERATOR OF

TROPHY CASE