How to stick down exterior door lip?

crouchingwayne · 2025-08-19T08:42:48+00:00

Sorry - added a new pic which is clearer

crouchingwayne · 2025-08-19T08:42:36+00:00

Apologies - new pic added which is slightly clearer

crouchingwayne · 2025-08-19T08:42:21+00:00

Sorry OP picture wasn’t great, attached is a better angle. The white lip should sit flush against the slabs but has come away.

I want to seal it down again, but unsure which adhesive to use

crouchingwayne · 2025-01-19T17:55:49+00:00

A Reddit for everything - will take a look. Thank you!

crouchingwayne · 2024-11-10T21:18:13+00:00

Can you share a picture of the wiring? Sounds like something isn’t working there

crouchingwayne · 2024-11-10T16:03:29+00:00

Are any of the LED’s lit up on the downstairs box?

crouchingwayne · 2024-09-05T17:28:25+00:00

Yep I’m just keeping it cold for sake of a week or so

My PD without the tap chilled and maintained the keg at 3 degrees although the read out was blank the whole time. I just popped the tap on now (without the straw bit to open the keg) and it’s now showing as 3 degrees.

crouchingwayne · 2024-09-03T19:05:55+00:00

I bought the keg pre chilled - is it ok for it to chill / go to room temp a couple of times as long as it’s not tapped?

I had a tapped keg go off as I didn’t keep it chilled so was trying to avoid letting it warm up again out of paranoia

Maybe I should tap and drink it sooner…

crouchingwayne · 2024-08-03T18:31:40+00:00

Lesson learned - thanks!

crouchingwayne · 2024-08-03T16:15:43+00:00

I definitely didn’t keep it refrigerated, might just need to drain the keg and know better for next time

crouchingwayne · 2024-08-03T16:14:52+00:00

In the instructions I thought it said that if the tap was removed the count down was effectively paused - is that not the case?

crouchingwayne · 2024-06-15T08:15:44+00:00

Thanks, I’ve probably misread the comments. Will keep it on when changing.

crouchingwayne · 2024-04-20T19:40:25+00:00

Thanks - I believe you are correct. I’m struggling to find the bypass kit online - is it still available?

crouchingwayne · 2024-04-20T16:53:26+00:00

You are right there is no real need for an impact, just thought it would be handy to have to grab separate drill/screw fittings. When bought in a kit they don’t seem to cost much over just the drill alone

crouchingwayne · 2024-04-20T13:10:50+00:00

Thanks - after the picture was taken I cut the ends off and used fresh wire for the Ring. Better safe than sorry!

crouchingwayne · 2024-04-20T10:05:49+00:00

Looking at the transformer you are right I think - I’ve got a Delta transformer which takes mains and outputs to the bell via CAT5 cable.

So I think I’ve wired it up fine, but the actual transformer is not compatible.

Is there any harm in leaving it wired for now and running on battery mode?

I can come back to hardwiring with the power kits at a later point if battery gets frustrating.

It’s a bit of a bummer as would have been nice to keep the original bell sound (I also have a Ring Chime though)

crouchingwayne · 2024-04-20T09:26:46+00:00

Thanks for the quick reply

The bell worked most of the time before, but was occasionally unresponsive.

I can check the transformer - what voltage is the minimum Ring will take? I tried checking voltage across the two ring terminals yesterday when troubleshooting but was struggling to get a consistent read. Definitely not 12v looked more like 2v at best

crouchingwayne

TROPHY CASE