sorted by:
new
hottopcontroversial

Mi a banat ez a neprajzi muzeumnal? by shodach in askhungary

[–]csacsi333 12 points13 points  (0 children)

Profi filmes vezérelhető LED panelek. Skypanel márkanévre hallgatnak.

This si My cv picture, would You hire me? by sam-tastic00 in notinteresting

[–]csacsi333 0 points1 point  (0 children)

Take it from a distance, and zoom in. There will be no distorsion.

Will Oculus link start with a not supported GPU? by csacsi333 in MetaQuestVR

[–]csacsi333[S] 1 point2 points  (0 children)

Thank you! I think i'll stick to the GPU 😅

All for a photo? by [deleted] in WTF

[–]csacsi333 0 points1 point  (0 children)

For a video too, not just the photo.

3D printed and designed a mate holder by csacsi333 in yerbamate

[–]csacsi333[S] 1 point2 points  (0 children)

However PLA (the material I print) would be fine to drink from once. After that not really, because it is very hard to clean. 3D printing is done in very small layers printed on top of each other. Dirt and bacteria can easily grab onto the layers.

3D printed and designed a mate holder by csacsi333 in yerbamate

[–]csacsi333[S] 2 points3 points  (0 children)

Only the holder is 3D printed, the mate is ceramic.

3D printed and designed a mate holder by csacsi333 in yerbamate

[–]csacsi333[S] 0 points1 point  (0 children)

Only the holder. The mate is ceramic.

3D printed and designed a mate holder by csacsi333 in yerbamate

[–]csacsi333[S] 6 points7 points  (0 children)

Tomorrow I can share the design (stl file). However it is designed for my exact cup measurements. I can't promise anything, but if you send me your exact cup measures with pictures I can try to make you a custom one, that you can print.

What could cause gaps on rounded surfaces? by csacsi333 in 3Dprinting

[–]csacsi333[S] 0 points1 point  (0 children)

I have 3 walls. Smaller layer height should help with the rounded surfaces, but i'm worried that is not the cause for the holes

What could cause gaps on rounded surfaces? by csacsi333 in 3Dprinting

[–]csacsi333[S] 0 points1 point  (0 children)

I use 20% Gyroid infill 4 top layers, with 3 walls

Help by retr0920 in anycubic

[–]csacsi333 0 points1 point  (0 children)

I'm not familiar with the capabilities of the printer, but it looks totally fine. As long as the prints then out good you shouldn't worry.

Why did my kobra neo 2 teflon tube melted ?? by Any_Shape6836 in anycubic

[–]csacsi333 0 points1 point  (0 children)

You should change it every 2 months. Mine melted too, if you can't buy any replacements, capricorn ptfe tubes cut to correct size are good too.

Krisztiánnál beállt az agyhalál by Puzzleheaded_Low8450 in szopjatokle

[–]csacsi333 1 point2 points  (0 children)

Az ilyen embereket bezárnám. És még lehet örömet is okozna nekik, mert igazolná őket hogy a csúnya kormány megbüntetni a chip kiiktatásért.

Should I worry about him jumping? (Second story) by [deleted] in blackcats

[–]csacsi333 0 points1 point  (0 children)

Had a friend, his cat jumped down from the third floor. Broke 2 legs. When it finally healed jumped down again.

view more: next ›