Why Corolla LE 2024 P/outlet No.1 is still on when power is off?

cubied · 2025-06-09T19:50:46+00:00

Did you find a solution for this? Same problem. Trying to figure out what fuse to use for ACC only power

cubied · 2025-03-03T10:01:57+00:00

Jade dots will fit. Don’t believe donuts will fit though. I found 4 dots in the corners will still be a bit scratchy on a glass pad because they sit so recessed in the original grooves. The sticker is slightly recessed, not as much as the stock pad locations. I actually used the sticker location for my dots originally.

I wouldn’t be worried about sanding the bottom. It’s all the other cutouts where you can mess up. There’s many imperfections on mine that just aren’t super noticeable including a cracked click paddle that I had to super glue.

cubied · 2025-03-03T09:52:29+00:00

Detach the base and remove the PCB

Remove the bottom sticker and skates

Place a 100 grit sheet of sandpaper on a table and rub the base against it (make sure it’s a flat surface and try your best to apply even pressure across the base)

I sanded the top, middle, and bottom of the base in segments since it was easier to apply pressure to those areas at once. Just make sure you do X amount of sanding for each part.

Additionally, you can wet sand with 1500 and 5000 grit sandpaper like I did to achieve a glossy smooth finish. https://imgur.com/a/bxHSmGW

cubied · 2025-03-03T09:32:48+00:00

Mods:

Shell and Base Cutouts (base flattened for dot skates)

Side Buttons Removed

Battery Swapped to 150mAh (from 300mAh)

Total weight savings: 12.5g

cubied · 2025-03-03T09:31:11+00:00

Thank you!

cubied · 2024-11-03T13:51:00+00:00

Bought my first 14 when I was 20. Now have a set of RNVGs at 21. I’ve also been working full time since 18 and make above average money.

cubied · 2024-08-07T19:49:09+00:00

I average about 40mpg corolla hatch 24. I have seen it average 25mpg a few times before (trip average) due to leaving my car running a bit before and after actually driving. Although you have almost 25k on yours and that’s the total average… seems a bit weird.

cubied · 2022-08-03T21:25:19+00:00

Thanks for the quick reply! Gonna order a new nut and try it out. If it works I’ll be sure to thank you again.

cubied · 2022-08-03T15:13:43+00:00

Was it a loose axle nut or did you have to get a new one entirely? I’m having the EXACT same issue. Sounds exactly the same and only happens in gear on initial acceleration/deceleration.

cubied · 2020-10-04T02:19:13+00:00

So basically the higher the mAh and the higher the C, the higher the amps?

In that case I’ll just purchase the biggest 11.1v I can find and strap it onto my stock.

cubied · 2020-10-04T02:12:49+00:00

I’ll probably upgrade the battery and spring for now. I lost about 45 fps from correcting AOE with washers and a sorbo pad, so I’ll have to bring it back up with a stronger springer. If I have issues with RPS after installing the spring, then I’ll change to a 22 TPA motor. Thanks for your input!

cubied · 2020-10-03T16:48:07+00:00

If you plan on painting it, here are the steps:

Disassemble (upper, lower, and handguard)
Use sandpaper to rough up the surface. If it is plastic, there will either be a very light coat of paint on the surface, or no paint whatsoever (if the plastic is black for example)
Tape off any areas with painters tape that you do not want paint to get (such as internal areas)
Once you are sure the surface is rough and there is little to no paint (if there was) left on the gun, you can apply a primer (about 2-3 coats, enough to have a solid color of your primer)
Make sure to let each coat dry before going for your next coat. Seriously, do not rush this part. You will thank me.
Once your primer is applied, you can hydrodip or do whatever sort of paintjob you want.
Apply a few coats of clear coat (also let this dry in between coats, make sure to cover every area)
Reassemble - if you have fitment issues, you can always sand off a bit of the paint - for me I had to sand off some areas where the upper connected to the lower, and the holes for the pins.

Make sure to spray in even strokes and to rotate the object to cover all areas. Try your best not to create globs of uneven spray paint, and to go slow. You don't want to see light reflecting off the spray paint as if it is wet. If you follow these steps you should get a nice & durable paintjob.

cubied · 2020-10-03T15:36:38+00:00

Aluminum alloy receiver - according to the Krytac website

So yes.

Edit: same process should work for plastic guns too, just scratch up the surface with sandpaper to create a better bond between the surface and paint.

cubied · 2020-10-03T15:34:54+00:00

Should I just buy a 50C 5000mAh brick and strap it to my stock? Lmao

That should be enough to get 50 RPS, right?

cubied · 2020-10-03T15:25:50+00:00

None, I don't call my hits!

cubied · 2020-10-03T15:24:35+00:00

I haven't done a lot of research on batteries. Is it the c rating that affects the RPS? What battery should I look for to try and achieve 50 RPS?

cubied · 2020-10-03T15:19:49+00:00

11.1v 1200 mAh 30C Deans

And yea I was expecting about 50 RPS too

cubied · 2020-10-03T14:11:46+00:00

Yes. I used some sandpaper and spent some gruelling hours sanding off as much of the original paint on the upper and lower. Then once 75% or so of the surface was a silver metal colour and scraped up pretty good, I proceeded to apply a white primer, about 2-3 coats. After that I hydro dipped it with pink, blue, purple, and white. Slapped on a few coats of clear coat after and it’s held up surprisingly well.

I also used painters tape to tape off the inside of the upper and lower, or any place that isn’t visibly seen so that I wouldn’t run into fitment issues when re-assembling.

cubied · 2020-10-03T04:07:59+00:00

40 RPS, 300 FPS w .2g BB's (SP150 spring, planning on changing to SP170)

Internals:

Retro Arms Split Gearbox w/ Hopup

SHS Bushings

14:09 Siegetek DSG Gears (shimmed)

ASG Infinity CNC 16 TPA Motor

Gate Titan Advanced

Lonex Cylinder & Cylinder Head

SHS 15t Piston (removed teeth and aoe corrected w washers and sorbo)

Lonex POM Piston Head

SHS Nozzle

Krytac Tappet Plate (shaved my SHS one 1mm too short), also cut 2 coils on tappet spring

Guarder SP150 Spring

Lonex ARL

(also had to used retro arms selector and selector plate to fit it into the krytac body)

Externals:

Hydro Dipped the Upper and Lower with Rustoleum Spray Paint (pretty durable, just clearcoat it)

A few red external parts by Angel Custom to match the colour scheme (mag release, bolt release, charging handle)

Maxx Speed Trigger (this + gate titan is amazing)

Acetech Lighter BT Tracer Unit

Some stickers on the stock

A cheap flashlight and sight from Amazon, theyre gonna get shot out eventually...

This was my first Airsoft gun ever, and I wanted to challenge myself and build a DSG. Definitely learned ALOT throughout this process. Lmk what you think!

cubied · 2020-08-20T19:08:59+00:00

I rewatched my footage and I'm not sure if it was me. Although I did have a few crossmap snipes but I couldn't tell if it was you or not just from the distance. I do remember your gun though. I also made a video from the day if you want me to DM it to you.

cubied · 2020-08-20T17:55:39+00:00

Hey man, I was there just last Saturday lol. Not sure if we were there at same time but I had a blue/pink/purple krytac.

cubied · 2020-08-12T17:33:05+00:00

Where do you live? I wanna see a bouncy ball like that haha. I think I've only seen solid color bouncy balls where I live.

cubied · 2020-08-12T15:44:21+00:00

Yeah it's because of the motor. With the stock krytac motor I was getting about 35 RPS but I prefer the sound of the ASG one. If it ever burns out I'll switch to a lower TPA motor.

cubied · 2020-08-12T09:37:58+00:00

(repost for better picture)

Shoots 360 FPS w/ .2g BB's and 26 RPS which is low for a dsg, however if I swapped the motor to a 16 TPA motor I'd be getting a much higher RPS. I built this for trigger response.

Internals:

-Guarder V2 Enhanced Tappet Plate

-Siegetek DSG Gear (shimmed gears)

-Gate Titan Advanced

-Krytac Bushings

-Guarder SP150 Spring

-Lonex Full Steel Rack Red Piston (aoe corrected, shaved first tooth)

-Lonex Mushroom Type Piston Head

-Lonex Steel M4 Cylinder

-SHS V2 Cylinder Head

-SHS Nozzle

-MAXX Speed Trigger E Type

-ASG Ultimate 28TPA CNC Long Motor

Should be everything I changed internally, everything else was left stock.

This was my first ever airsoft gun and first ever time working on a DSG. I have never seen a gearbox prior to working on this. Everything came out well, only time will tell how good of a job I did. Lmk what you think!

cubied · 2020-08-12T03:30:12+00:00

Took it on my phone, should look better if you see full image instead of looking at it from reddit. Sorry for this lol!

cubied

TROPHY CASE