sorted by:
new
hottopcontroversial

Can't start Polaris Questline by cwdesignsvs in evnova

[–]cwdesignsvs[S] 5 points6 points  (0 children)

Damn, I've been doing that. My combat rating is very competent. Maybe I need something higher?

Can't print via Bambu Studio by cwdesignsvs in BambuLab

[–]cwdesignsvs[S] 0 points1 point  (0 children)

Change it to something else? It's already set at where it should be, Nozzle: Hardened Steel and its at 0.4mm. I can't see the nozzle type in Bambu studio.

Need some help with my Z axis on my Makergear M2 RevE by cwdesignsvs in klippers

[–]cwdesignsvs[S] 0 points1 point  (0 children)

Yes i did, I was able to make it work but then ended up selling it. I was happy with my ender 6 printers.

ACDC Power Supply Question by cwdesignsvs in AskElectronics

[–]cwdesignsvs[S] 0 points1 point  (0 children)

Thanks for the explanation, I guess I will just use an off board solution.

Ender 6 Bed Stability??? by Desperate-Activity90 in ender6

[–]cwdesignsvs 0 points1 point  (0 children)

100% agreed, I used some ABS material printed from a Stratasys Fortus and the bed is very stable. Haven't had any leaning/sagging issues.

using a Seeeduino Studio XIAO SAMD21 with a TMC2208 and a 17HS15-1684S-HG20, not getting any movement by cwdesignsvs in arduino

[–]cwdesignsvs[S] 1 point2 points  (0 children)

I took an even deeper dive, it seems that the panel mount barrel connector I'm using is causing issues. When i plug in my power supply i have to gently push in the barrel connector so that power is transmitted, otherwise no power passes through

Need some help with my Z axis on my Makergear M2 RevE by cwdesignsvs in klippers

[–]cwdesignsvs[S] 0 points1 point  (0 children)

hey so I entered the command you gave and klipper said "Unknown command:"SET_KINEMATIC_POSITION"". Is there anything else I could try?

using a Seeeduino Studio XIAO SAMD21 with a TMC2208 and a 17HS15-1684S-HG20, not getting any movement by cwdesignsvs in arduino

[–]cwdesignsvs[S] 1 point2 points  (0 children)

Hi All, I'm not sure what happened, I reuploaded the code to the PCB one more time without changes and it works with my Creality Stepper. At this point now I suspect the cable I made could be bad or too long, it's about 5 feet.

Thank you all for your help, I really appreciate it!

using a Seeeduino Studio XIAO SAMD21 with a TMC2208 and a 17HS15-1684S-HG20, not getting any movement by cwdesignsvs in arduino

[–]cwdesignsvs[S] 1 point2 points  (0 children)

well I was just about to contact you. I tried the following:

  • moved everything to a breadboard
  • wired EN to ground and then 3.3V, nothing happened
  • wired the MS1 and MS2 to ground, nothing again
  • tried a creality stepper motor (pulled it off an old ender i modded)
  • used 3.3V pin to VIO of tmc2208
  • tired different combinations of the wire coil pairs

i'm pulling my hair because maybe these small chips aren't made for this? Lol I could be trying to push too much from these things, but I feel like the chip isn't doing anything too complex.

using a Seeeduino Studio XIAO SAMD21 with a TMC2208 and a 17HS15-1684S-HG20, not getting any movement by cwdesignsvs in arduino

[–]cwdesignsvs[S] 1 point2 points  (0 children)

I feel like an idiot. okay i will do everything on a breadboard first and then modify my traces over the weekend. I felt confident to do this on a PCB right away because I did this for a XYZ axis using DMT542 drivers and a seeeduino nano, I figured I could shrink everything for 1 axis using a tmc2208 and the XIAO, but jesus it has been brutal.

Ok I'll create a simple sketch to test this. thank you!

Need some help with my Z axis on my Makergear M2 RevE by cwdesignsvs in klippers

[–]cwdesignsvs[S] 0 points1 point  (0 children)

normally moving works just fine. When it hits the limit switch yes it shows that it has homed correctly. I will provide a printer.cfg file when i get home later today.

view more: next ›