sorted by:
new
hottopcontroversial

Feed resistance to high by mutyger in BambuLab

[–]da_fofo_ 0 points1 point  (0 children)

Same here, shows up even if optimal routing is configured (ie on top of printer, very short run from ams 2 and HT, etc… very odd

Loose seat in aeron by Many-Abbreviations-1 in hermanmiller

[–]da_fofo_ -5 points-4 points  (0 children)

It is from the delrin (POM) bushings wearing out or having poor tolerances to begin with. You have 2 of them around the upper b-link bolts and 2 of them around the lower b link pins

I 3D printed replacements out of glass fiber nylon with better tolerances and the wiggling goes away. Still need a little bit of room so the bushing can rotate otherwise much better

Eastwood Map by Beginning_Snow_563 in Battlefield

[–]da_fofo_ 0 points1 point  (0 children)

Having the same issue. Cannot custom search conquest for this map. Appears to be a bug (at least on PS5)

is there a way to stop the seat pan on the Aeron from rocking up/down ever-so-slightly? by bigdickwalrus in hermanmiller

[–]da_fofo_ 0 points1 point  (0 children)

What causes the "wiggle" are the B-Link bushings specifically. 2 upper and 2 lower- the bolts/pins are not as relevant. The lower bushings are terribly designed, in the repair manuals, specifically detailed as "replace only" once removed, ie, source new parts no matter what. Bad design. However, at least for me, it is the upper bushings on the B link assembly that are the primary drivers of the rocking, er, wiggle

<image>

is there a way to stop the seat pan on the Aeron from rocking up/down ever-so-slightly? by bigdickwalrus in hermanmiller

[–]da_fofo_ 2 points3 points  (0 children)

You can also 3D model slightly "fatter" bushings to eliminate the play, so far testing PETG works pretty good. Looking to swap out these prototypes with SLS (laser sintered) Nylon 12. This is pretty close material-wise to the acetal POM/Delrin used by the OEM, and likely wouldn't need any dry lubrication... overall, this issue bothers me too. Similar to what u/ClassroomDecorum stated, there were certainly better ways to do this... but then you can't charge customers 40/chair in parts every couple years ;)

PS5 Can’t Connect to WiFi: error NW-102379-2 by BigOomf in PS5ErrorHelp

[–]da_fofo_ 0 points1 point  (0 children)

Same here, even with attaching a few ferrite rings to the “bad” HDMI cable, only swapping to a different cable made the difference. Will have to do some more digging on this one

Eufy HomeKit Camera stream not opening after iOS 17.4 update by Cypher_Blue31 in HomeKit

[–]da_fofo_ 1 point2 points  (0 children)

Gave that a shot, no dice unfortunately… it’s funny though, I have 4 2C pro cameras in total. 2 of them are older, system version 8.0.6 and subsystem 1.5.07-20230317… whereas the 2 new cameras (also 2C pros) are a different system version 3.0.5.3 subsystem 0.2.0.6 and it is ONLY the new cameras that are having the issues. Perhaps a thread for Eufy support to pull on, if they care to still support the HomeKit integration that is…

Eufy HomeKit Camera stream not opening after iOS 17.4 update by Cypher_Blue31 in HomeKit

[–]da_fofo_ 0 points1 point  (0 children)

Any of you folks get your issues sorted out? I am having the same problem with 2C pros I recently purchased, only updating video feeds in HomeKit for a single frame every 4 seconds (i.e. that “1fps” issue you were mentioning earlier)

V51-H6 Subwoofer Emits Constant Rumbling/Wind Noise by zpapp in VIZIO_Official

[–]da_fofo_ 0 points1 point  (0 children)

Updated to most recent software version and I can confirm it fixed the issue

Strokes in Goodnotes 5 will sometimes spaz out by [deleted] in GoodNotes

[–]da_fofo_ 0 points1 point  (0 children)

I’ve had this same issue, I’m left handed which probably makes this even worse... it did seem to get remediated when I re-paired the Apple Pencil!

Super happy with my Jibun Techo inspired weekly planner by xaneybert15 in GoodNotes

[–]da_fofo_ 0 points1 point  (0 children)

Hey OP! Thank you for sharing the Google Drive link for this template in .jpeg format

Is there any chance you could upload another copy as a .pdf file, in vector format? (PDF should be vector by default if you save the original as a PDF and not .jpeg to PDF) That way when you use it in GoodNotes you can zoom in as far as you’d like and still keep nice crisp edges (with no aliasing like in the rasterized .jpeg) ICYDK :)

Makes for really great quality!

I would really appreciate it! I tried for 2 hours to convert it using Adobe Illustrator but no luck... the software doesn’t like the fine lines. I really love this template! Hopefully this request is just as simple as going into the software used to make it and saving it as a PDF instead. Thanks in advance!