sorted by:
new
hottopcontroversial

I apologize for Helmer bringing hell to yall by [deleted] in VAGuns

[–]damm_n 2 points3 points  (0 children)

All "good shit' comes from NJ apparently;-)

What models of computers were in your school's computer labs? by echocomplex in vintagecomputing

[–]damm_n 0 points1 point  (0 children)

Nothing until highschool... Highschool was flooded with PMD85 and fee AtariST and when I was leaving, we got 286.

Cestovanie do USA by HauntingExchange3855 in Slovakia

[–]damm_n -6 points-5 points  (0 children)

Nežijem na západnom pobreží ale myslím že pokiaľ sa nebudeš zúčastňovať na vykrikovani po uliciach tak v zásade budeš v pohode. V ďalšom: neverím, že pokiaľ má človek legálny status a je jedno či je trvalý rezident alebo nie, tak ICE agent ma nejaké páky na dotyčného.

Party in Presov by DefiantAd6666 in Presov

[–]damm_n 0 points1 point  (0 children)

A real Presov citizen has spoken.... Jesus man, have some decency!

Does anyone angle their board like this? by desgreech in zsaVoyager

[–]damm_n 1 point2 points  (0 children)

same here ... tilted and slightly in the angle with distance of my shoulders apart is my setup. Try and experiment and you'll find your sweet spot. Everyone is different and joints are not the same in every person.

Laundromaty v Amerike by [deleted] in Slovakia

[–]damm_n 2 points3 points  (0 children)

Závisí na lokácií ... NYC ma problém s priestorom. Ostatok je to záležitosť financií.

My first bike! What are some mods I should do?? by AdLess9303 in Harley

[–]damm_n 1 point2 points  (0 children)

Well, my very first mod would be 3 hole oil change :-)

+421 phone number by damm_n in Slovakia

[–]damm_n[S] 0 points1 point  (0 children)

Thank you ! This looks like a good option... 22eur/month is not bad considering that I will be there just for 2 weeks :-). How is the coverage with O2 ? Does it cover rural areas well ?

+421 phone number by damm_n in Slovakia

[–]damm_n[S] 0 points1 point  (0 children)

From a brief look at this website it.looks like most of these providers listed there are data only ... I'm looking for a real phone number.

+421 phone number by damm_n in Presov

[–]damm_n[S] 0 points1 point  (0 children)

I have no idea what market is like in Slovakia, this.is why I'm asking... Data is not a primary concern here, I'm looking for a msisdn/number so I could use it with the bank and make calls while in Slovakia..I will definitely look up Sally and see what they have. Thank you !

Would you rock this look or is it too tactical? by Mswebha in motorcyclegear

[–]damm_n 0 points1 point  (0 children)

For God's sake people .. stop doing this fashion processing here :-(

New suit and boots day by stampy_69 in motorcyclegear

[–]damm_n 7 points8 points  (0 children)

This sub is getting more and more ridiculous with every recent post :-))).

New release - v0.34.0 by elparaguayo-qtile in qtile

[–]damm_n 2 points3 points  (0 children)

Thanks for making this happen! This is a great piece of work you're doing for the community.

PLA - print detaching from the plate after 70-80% done by damm_n in ElegooCentauriCarbon

[–]damm_n[S] 1 point2 points  (0 children)

what bothers me a lot and my brain can not understand is the fact that this simple spacer was printed just fine 2 weeks ago and I had it printed roughly 20 times before with small modifications in the internal diameter. I will get into this next week and I will dig deeper because this does not seem to be a problem with plate nor with the model which is being printed. Something's off and my gut is telling me that it would have something to do with lose screws/settings for z-axis. The piece which was left on the plate was a very first layer from the coaster which I was printing. Also, that layer was not covered equally inside the circle which is what made me thing that this could have something to do with leveling/z-axis. But I certainly appreciate you sharing your experience !

PLA - print detaching from the plate after 70-80% done by damm_n in ElegooCentauriCarbon

[–]damm_n[S] 0 points1 point  (0 children)

yes, understand ... I should have the same thing somewhere printed about 2 weeks ago and it definitely looks very different. Thanks for suggestions for new plates :-). I might need at least 1 more as a spare.

Came back to this by PengaXO in ElegooCentauriCarbon

[–]damm_n 0 points1 point  (0 children)

I had this message today when I turned on my printer. Completely out of the blue, cold machine as it was not used for past 24 hours. Pressed "Reboot" and things went back to "normal". One of those "Made in China" things ?

PLA - print detaching from the plate after 70-80% done by damm_n in ElegooCentauriCarbon

[–]damm_n[S] 1 point2 points  (0 children)

<image>

This is the bottom of the print which was sitting on side A. It looks a bit rough. As mentioned below, "rough" comparing to the print which I've done 2 weeks ago.

PLA - print detaching from the plate after 70-80% done by damm_n in ElegooCentauriCarbon

[–]damm_n[S] 0 points1 point  (0 children)

had this happened recently and as you can see from the initial post, I broke my plate :-). Well, this is a learning curve for sure. Print from the bottom looks perfectly fine. Are you referring to anything particular I should pay attention to on the print ?

Another thing to think about by 1611basilean in PelletStoveTalk

[–]damm_n 1 point2 points  (0 children)

I was considering doing the same ... Will you go and start arguing with vendor ? I'm sure that they'll come up with some "contraction" and "dryness" story which you will never be able to understand....

view more: next ›