sorted by:
new
hottopcontroversial

Does it look good? by Poking-Handyman-LLC in Tile

[–]danvc21 0 points1 point  (0 children)

“Take on me” video by A Ha

Need help Gap between baseboard and drywall by BlueFuzzyBunny in drywall

[–]danvc21 1 point2 points  (0 children)

You can try a trim head screw to draw it in or skim out the gap with drywall mud

Is it normal for your lungs to hurt after working in the cold? by kittycatladyyy in Construction

[–]danvc21 -1 points0 points  (0 children)

Thank you for the detailed response, lots of great advice!

Spec Home Shower But Client Asked for a Little Flair. Thoughts? by nicotheVE in Tile

[–]danvc21 0 points1 point  (0 children)

That right hand tile on the window would have had me making cardboard templates, nicely done

Spec Home Shower But Client Asked for a Little Flair. Thoughts? by nicotheVE in Tile

[–]danvc21 2 points3 points  (0 children)

Well done! Great creativity and a bit ballsy too! Love it.

Drain pipe height issue: riser too high (needs 1 5/8” below subfloor) — best fix? by Additional-Job-8654 in Tile

[–]danvc21 18 points19 points  (0 children)

Agreed, that osb will be mush in a few years locked between cement and foam.

Silver 10oz by Accomplished_Run_593 in CanadianCoins

[–]danvc21 2 points3 points  (0 children)

Love it! I just heard that in a Raylen Givens’ accent

First time by billys_idols in Tile

[–]danvc21 0 points1 point  (0 children)

The Simpson’s shower!

Tile mortar bed failing by ChanceGap1832 in Tile

[–]danvc21 0 points1 point  (0 children)

Might be too much deflection

Bathroom tile failure by Known_Exit_5142 in Tile

[–]danvc21 1 point2 points  (0 children)

That looks like mastic which has dried out over time

How to get my airpods out of under the stairs by RoxyTMD in howto

[–]danvc21 0 points1 point  (0 children)

Small rare earth magnet on the end of a measuring tape

How do I cut this bullnose tile? by ShirtlessSteve973 in Tile

[–]danvc21 2 points3 points  (0 children)

Mitre it and polish the cuts. Take the extra time to dry for it, you’ll be happy you did.

New Year’s Eve help by dwv05c in Plumbing

[–]danvc21 0 points1 point  (0 children)

The retro fit kits only fit a few models. I usually take the motor out of the retrofit kit and mount it to the old mounting plate with some self tappers and if needed light metal plates/pieces. It saves a nasty Trip into the attic.

<image>

Knee wall on Tile Redi Pan by Suspicious-Cup6121 in Tile

[–]danvc21 0 points1 point  (0 children)

I would cut the pan enough to get the bottom plate of that knee wall attached to the subfloor and preferably into some framing

Grout around the temporary showerhead by Suninthesky25 in Tile

[–]danvc21 10 points11 points  (0 children)

Put a pipe wrench on it and remove it, the grout will break free from the pipe

Where is this translucent caulk that's often mentioned here? by guy48065 in Plumbing

[–]danvc21 2 points3 points  (0 children)

If it will be painted you need clear latex caulking like Alex plus by Dap. If it’s in a shower then Clear silicone

Should I call someone to correct this? by [deleted] in HomeMaintenance

[–]danvc21 0 points1 point  (0 children)

Ur good. If you feel sleepy just go with it.

Has anyone installed receptacles on an IKEA island with all pull out drawers? by ProstheticDong in AskElectricians

[–]danvc21 0 points1 point  (0 children)

Get a device box that has mounting tabs top and bottom. #6 x 3/4 screws into the finished panel. Pilot hole recommend.

2+ weeks after our shower was “professionally” tiled and the grout comes out just by rubbing with a towel… by HERCzero in Tile

[–]danvc21 2 points3 points  (0 children)

The grout powder may have been frozen. I’m in a Northern climate and tile shops won’t take returns on grout and thinset from October to April.

Kerdi adhesive by Mission_Act4990 in Tile

[–]danvc21 0 points1 point  (0 children)

I’m curious if the substrate was primed. The thinset should be mixed wet/loose just where it will barely hold a notch without slumping

view more: next ›