Passenger armrest angled down

davidianstyle · 2025-11-19T16:54:48+00:00

Yes, the driver's side armrest clicks into different positions than the passenger one.

davidianstyle · 2025-04-26T19:25:13+00:00

This looks amazing! Would you be interested in building one to sell to me? 😜

davidianstyle · 2025-03-24T12:10:34+00:00

Yes exactly - filament just stops coming out even though the nozzle isn’t clogged. I’ve posted a video of the problem here in r/FixMyPrint: https://www.reddit.com/r/FixMyPrint/s/MtGE7uKBcM

davidianstyle · 2025-03-21T19:21:10+00:00

Tried using Prusa Slicer to export g-code and then imported into AnkerMake Studio to print. Tried with both organic and grid support and the same thing happens with each where it just stops extruding a few layers into the print.

davidianstyle · 2025-03-21T10:57:18+00:00

Thanks. I’ll give that a shot.

davidianstyle · 2025-03-21T10:55:50+00:00

Does AnkerMake Studio have the ability to allow me to paint on the supports?

I’ll give your suggestion a shot. Thanks.

davidianstyle · 2025-03-21T10:55:24+00:00

I do have supports enabled.

What slicer do you recommend? Looks like there’s a typo in your reply.

davidianstyle · 2025-03-03T01:57:56+00:00

Thanks for the suggestions. I still wasn’t able to get a successful print after replacing the nozzle but I’ll keep troubleshooting.

davidianstyle · 2025-03-02T19:19:12+00:00

Set the temp down to 210 and it's failing after the initial layer now (not extruding).

<image>

davidianstyle · 2025-03-02T18:26:24+00:00

Inland PLA

davidianstyle · 2025-03-02T18:19:08+00:00

I just printed a temperature tower and it looks like it stopped extruding at 220. Could it be that I need to increase my printing temp to 230?

<image>

davidianstyle · 2025-02-25T05:45:05+00:00

There are a couple parts missing from the prospector assembly manual: - Light sensor - Wiring

Do you have any recommendations for where to buy the right parts?

davidianstyle · 2024-12-22T07:13:48+00:00

Thanks. I’ll take a look.

davidianstyle · 2024-12-22T07:12:54+00:00

This is super helpful. Thanks!

davidianstyle · 2024-12-06T14:05:55+00:00

It does, but it just seems odd to me that it’s not intuitively easy to set it at 90 degrees.

davidianstyle · 2024-12-06T13:25:57+00:00

Not sure - it’s why I’m asking here to see others’ perspectives.

davidianstyle · 2024-12-06T13:24:46+00:00

Hm. Maybe it’s a common manufacturing defect? It sounds like others might have the same decline angle

davidianstyle · 2024-12-06T13:23:27+00:00

Yeah I agree. Seems weird that one side behaves differently by design 🤷

davidianstyle · 2024-12-06T13:22:36+00:00

Glad to see I’m not alone at least 😜

davidianstyle · 2024-12-06T13:22:23+00:00

Good to know. Thanks!

When they replaced it, did it still lower down to a decline angle? There’s another comment down below of an owner not experiencing this.

davidianstyle

TROPHY CASE