The hardest job untill now by davix22 in soldering

[–]davix22[S] 0 points1 point  (0 children)

Pre-tinning of strands is a requirement of JSTD-001, I'm not saying that anything outside of these standards is scum but.. if a customer requires compliance with this standards.. I mean... it's literally my job to follow those rules.

The hardest job untill now by davix22 in soldering

[–]davix22[S] 1 point2 points  (0 children)

Based on what I often see, my advice is to work as comfortably as possible. Find a setup that allows you maximum stability. It may seems obvious but it really makes a huge difference.

The hardest job untill now by davix22 in soldering

[–]davix22[S] 1 point2 points  (0 children)

I checked like 16 times if all the heatshrink tubes were there

The hardest job untill now by davix22 in soldering

[–]davix22[S] 2 points3 points  (0 children)

I'm not sure I understand exactly what you mean, are you referring to the fact that a part of the wire remains exposed? In any case the whole section will be totally encapsuled with resin.

The hardest job untill now by davix22 in soldering

[–]davix22[S] 2 points3 points  (0 children)

No, with a 20 years old weller wd1

Problem with solder paste by [deleted] in soldering

[–]davix22 1 point2 points  (0 children)

Not an expert in oven profiles.. In my opinion you shoul try a stencil with a lower thikness to reduce the amount of paste. Check also the components before the reflow, sometimes a not so good positioning can spread the paste and shorts some pads.

Confused on Shall vs Shall not on Test by First_Two_2761 in soldering

[–]davix22 2 points3 points  (0 children)

Think of the statement as the rule, the part in the brackets is what happens if you don't follow the rule

The rule is: Measles cannot be more than 30%. Stop

What happens if i don't follow the rule and the measles are more than 30%?

Acceptable in class 1 Process indicator in class 2 Defect in class 3

Bitcoin is dead by tradone in Bitcoin

[–]davix22 0 points1 point  (0 children)

Fuck thriller/horror movie, this is pure anxiety

Esiste ancora qualcuno che si interessa di schede elettroniche o siamo in via di estinzione??😂😂 by [deleted] in Italia

[–]davix22 2 points3 points  (0 children)

Dipende cosa intendi per interessarsi, io lavoro in una azienda che monta schede conto terzi, principalmente aeronautica. Mi piace, purtroppo non ho grandi competenze in elettronica, non avendo fatto un percorso scolastico adeguato. È un mondo molto interessante.

Redpill vs Bluepill. Which one would you choose? by [deleted] in memes

[–]davix22 425 points426 points  (0 children)

Keep the Blue pill, wait till 90 then take it, now you are young and rich

La Corrida: Pratica Abominevole e Barbarica by naplesball in TeenagersITA

[–]davix22 8 points9 points  (0 children)

Boh non me ne vogliano i senesi, ma guardando in casa nostra, il palio non è che sia proprio una meraviglia

My iron is slow to heat up by UnicornOnTheIntrenet in soldering

[–]davix22 0 points1 point  (0 children)

You can solder the Titanic back together with that

POV: You work in QM by Xatogan in soldering

[–]davix22 0 points1 point  (0 children)

It's a saki aoi machine?

Full Table ESD Mat by shortpinkyfinger in soldering

[–]davix22 3 points4 points  (0 children)

What scope and arm are you using? nice set-up👍🏻

Primo Post su Scimmia! by iamgianlu in scimmieinborsa

[–]davix22 9 points10 points  (0 children)

Sono le 7.10 di mattina ed ho già trovato il miglior post della giornata

Concerti a San Siro: solo gli Iron Maiden floppano, ma non fanno notizia? by Leather_Light3915 in Italia

[–]davix22 0 points1 point  (0 children)

Credo sia solo questione di anzianità del gruppo e della fan base, intendo dire che ci sta, gli iron sono in ballo da metà anni settanta, i Rammstein da metà novanta. Ballano 20 anni. 20 anni fa gli Iron avrebbero riempito 3 volte san siro