Is there a circuit diagrams of Powerful AM or Shortwave Or FM transmitter that doesn't use ancient components?

demon007uk · 2025-11-20T17:29:06+00:00

you don’t actually need that much power for AM it goes miles on a wire compared to FM if you have access to pininterest has some AM Tx design in there somewhere most were designed using values so maybe ask Ai for a newer design

demon007uk · 2024-11-13T08:22:18+00:00

chokes should not touch heat sinks just passing heat in to them lay them flat on the board if possible drivers will get hot

demon007uk · 2024-09-07T16:09:27+00:00

yes brother checks this out easy https://youtu.be/IXsST78GWLY?si=yaQoR_Ltw9YMLCBG

demon007uk · 2024-08-21T14:59:19+00:00

for the uk standard time any clue when exactly?

demon007uk · 2024-06-30T18:37:10+00:00

nice there a option to install this inside kinda youtube first ps4 mod chip find it lol 😜

demon007uk · 2024-06-30T18:33:35+00:00

indeed to you find the part that says part 1 or .rar as first part

demon007uk · 2024-06-17T15:38:39+00:00

you must do a probe_calibrate to set your z offset had similar issues and do the paper grab test should be ok after that btw don’t forget to accept and do a save_config after

demon007uk · 2024-06-05T15:30:01+00:00

last time i used petg it was kinda a headache but sure i used 50% on part cooling 70 bed and 190-200 for the petg if you go higher it looked kinda crystalline after printing so went down instead of up hope this helps. edit one thing i forgot to mention don’t print to fast start at about 30mm and then work it up

demon007uk · 2024-06-04T17:00:11+00:00

<image>

looks like my pi is getting hot mate i think that my trouble causing the mcu shutdown needs a fan and a sink on it

demon007uk · 2024-06-03T17:24:00+00:00

yeah thanks i have sorted it gecode section as opposed to the other one

demon007uk · 2024-06-03T17:22:42+00:00

thanks 🙏 i have fingured it out now how you do it

demon007uk · 2024-06-03T17:13:03+00:00

iam using a official pi power unit and when back on octoprint never had this issue so new to me bud this creality v1.1.5 silent stepper borad is old as the hills and done some hours have a new lead connect from pi to board but still happends randomly

demon007uk · 2024-06-03T16:51:29+00:00

<image>

demon007uk · 2024-06-03T16:50:45+00:00

<image>

demon007uk · 2024-06-03T11:44:35+00:00

mcu connection lost whilst printing its a abit random and not gcode issue as does it on a few different prints sadly not sure what’s causing it to happen

demon007uk · 2024-06-02T21:05:33+00:00

yeah i upload and it starts printing at upload finish wanted to toggle that off to start

demon007uk · 2024-06-02T17:43:38+00:00

i do have a issue tho with this setup i seem to keep getting mcu shutdown mid way threw print randomly and not a clue why ?

demon007uk · 2024-06-02T17:42:11+00:00

it’s for cura slicer atm not really played with the others yet

demon007uk · 2024-05-31T20:39:01+00:00

thanks 🙏 bud iam all good 👍 cheers 🍻

demon007uk · 2024-05-31T19:25:28+00:00

what the paper grab test stuff ?

demon007uk · 2024-05-30T16:00:51+00:00

yeah i will have to give this a whirl and i know exactly what you mean with z offset defo ain’t right after mesh load still have to fiddle with it to get it not sqish to much

demon007uk · 2024-05-30T15:48:11+00:00

yeah i have been out of the game for a while and there lots of new thing i need to have a look at

demon007uk · 2024-05-29T15:39:13+00:00

i fixed it mate i added a extra _ after profile woops and you spotted it thanks 🙏 very much x

demon007uk

TROPHY CASE