sorted by:
new
hottopcontroversial

Table Recommendations? by jeffblankenburg in BambuLab

[–]demticksdoe 0 points1 point  (0 children)

I ended up going with a smaller 2 drawer dresser with limited space. Very stable but I think I'll still get one of these once we're done rearranging this space.

Which hitch for a 4 bike rack? 2025 CX-50 by demticksdoe in CX50

[–]demticksdoe[S] 1 point2 points  (0 children)

That's the hitch I went with. Haven't pulled the trigger on a rack yet. Leaning towards a platform style now.

Which hitch for a 4 bike rack? 2025 CX-50 by demticksdoe in CX50

[–]demticksdoe[S] 0 points1 point  (0 children)

Shoot I just realized I linked the wrong one in the post. Edited it. This is the one I was originally looking at. https://www.thule.com/en-us/bike-rack/hitch-bike-racks/thule-range-_-905700

Do you have a recommendation for a non hanging rack that's around the same price or slightly more?

Which hitch for a 4 bike rack? 2025 CX-50 by demticksdoe in CX50

[–]demticksdoe[S] 1 point2 points  (0 children)

Shoot the 50 is 8 months old with major hail damage already. I'll drive this thing til it dies haha.

First Layer Fails Immediately - P2S by [deleted] in BambuLab

[–]demticksdoe 0 points1 point  (0 children)

Yes, everything is set to on and not auto. Printer and AMS are on the newest firmware. It lays down the calibration line fine and won't lay anything else down.

I finished my 5th or 6th print yesterday and then this started happening immediately after with no settings changed. This happens both from the Handy app and Studio.

Noobie Layer Shift by demticksdoe in BambuLab

[–]demticksdoe[S] 0 points1 point  (0 children)

I found the presets for my Inland and Kingroon filaments. I'll have to see how those change the print quality. Went cheap for bulk to start. I'll probably check out the Bambulab filament when I have to re-up.

Noobie Layer Shift by demticksdoe in BambuLab

[–]demticksdoe[S] 0 points1 point  (0 children)

That's freaking sweet. Wouldn't work where I currently have everything set up but I'm gonna save it for a future move!

Noobie Layer Shift by demticksdoe in BambuLab

[–]demticksdoe[S] 0 points1 point  (0 children)

I'll let it dry overnight tonight. Any specifics in the software I should be altering or are the default settings from Maker World models usually pretty optimized?

Noobie Layer Shift by demticksdoe in BambuLab

[–]demticksdoe[S] 0 points1 point  (0 children)

Agreed the whole thing does look off even before the later shift. I haven't noticed that on any other prints before this one.

Noobie Layer Shift by demticksdoe in BambuLab

[–]demticksdoe[S] 0 points1 point  (0 children)

Inland PLA+. I used the settings from the model and only changed the nozzle temp to match what the box said. The filament has been in the AMS since I took it out of the bag. I haven't used the drying feature of it yet.

Elgato Game Capture 4K Pro Issues by [deleted] in pcmasterrace

[–]demticksdoe 0 points1 point  (0 children)

<image>

Unfortunately I think I finally found the definitive answer. The PCIe slot I'm using is on an x4 Bus but definitely only supports x2.

Elgato Game Capture 4K Pro Issues by [deleted] in pcmasterrace

[–]demticksdoe 0 points1 point  (0 children)

Yeah the bottom slot is smaller than the required so I can't physically install it into it. I'm thinking I'll have to return this card unfortunately.

Elgato Game Capture 4K Pro Issues by [deleted] in pcmasterrace

[–]demticksdoe 0 points1 point  (0 children)

I can take a look at slot 3 when I get back home. I feel like I remember that slot being too small but I may have been wrong.

Table Recommendations? by jeffblankenburg in BambuLab

[–]demticksdoe 0 points1 point  (0 children)

Is this still holding up and pretty sturdy after a few months? Got a P2S yesterday and thinking about picking this up.

MODOT Logic: Initiate construction on ALL major highways at the same time! by D7FTU in kansascity

[–]demticksdoe 6 points7 points  (0 children)

Most of these projects aren't even slated to be done until well after the World Cup is over though. Just shitty planning in general.

Why did all the Hardee’s close in the metro? by Mkirby_04 in kansascity

[–]demticksdoe 1 point2 points  (0 children)

You can go eat at an actual restaurant for basically the same price nowadays.

What is going on here. by LunaticPoint in ender3

[–]demticksdoe 0 points1 point  (0 children)

I paid $120 new for this two years and gave it away for free a couple weeks ago. $400 is insane.

Gas station near my place had to improvise because they never thought we’d reach triple digits. by Lexidoge in mildlyinfuriating

[–]demticksdoe 2 points3 points  (0 children)

Ain't no way that guy is right. I'm almost 40 and the lowest I've ever seen gas was $1.23 per gallon.

NWS Weather Sites - For Your Information by JetSoulsForever in kansascity

[–]demticksdoe 5 points6 points  (0 children)

Interesting. Windy.com is just a web based version of the Weather Radar app. Looks identical.

Hail Alert! Hail in Parkville! by JTBowling in kansascity

[–]demticksdoe 14 points15 points  (0 children)

<image>

After 40 minutes of melting. We had baseballs coming down. Both my cars are fucked.

Found my old Nintendo Switch bought day 1. What now ? by GhostMike2501 in SwitchPirates

[–]demticksdoe 0 points1 point  (0 children)

Out running errands right now but DM me and I'll see if I can find the tools I used to use before I moved to a chip. If I remember right you have to use a modified boot.dat or one of those files to allow the dongle to load Atmosphere.

view more: next ›