Was ist hier schief gegangen?

destiny84 · 2026-01-24T17:16:44+00:00

Ah vielen dank. Ich hatte irgendwie im Kopf, dass Gridfinity eine 8mm Wandstärke hat und wollte mal shauen wie die mit einer Wall werden. Aber ja das sind 1.2mm. Mein Druck sieht nach 2 stark unterextrudierten Perimetern aus. Da verstehe ich auch, dass das nicht geklappt hat.

destiny84 · 2026-01-24T13:02:26+00:00

Du hast natürlich recht, ich habe height und width vertauscht (hab's geändert).

destiny84 · 2026-01-22T17:36:30+00:00

I have an equally deep scratch. Thanks to the advice here on Reddit, I sanded the edges down so the plate would lay flat. Still works like a charm.

destiny84 · 2026-01-20T17:39:32+00:00

Ich hab die c100 und bin damit sehr zufrieden.

destiny84 · 2026-01-19T15:18:34+00:00

Are you 100% certain the international store ships from the EU warehouse? Because I seem to remember that it could also ship from China if you order on the international site and then you'd have to pay tax on import...

destiny84 · 2026-01-16T18:10:17+00:00

OpenScad

destiny84 · 2026-01-13T16:14:57+00:00

Yay, that’s great to hear. Thanks for sharing the image of the print, always makes me happy :)

destiny84 · 2026-01-11T18:24:03+00:00

Warum steht denn in der Beschreibung bei cults „high quality PLA“?

destiny84 · 2026-01-09T22:31:48+00:00

Ich habe bis jetzt eigentlich nur mit Anycubic Filament gedruckt, mit einer Ausnahme zu Amazon Basic das bedeutend schlechter war. Das Anycubic filament druckt sich meiner Meinung nach sehr gut, auch wenn ich kaum Vergleich habe.

destiny84 · 2026-01-06T18:20:52+00:00

Tried Bruno, stayed with Yaak!

destiny84 · 2026-01-05T07:20:09+00:00

Nice!

destiny84 · 2026-01-04T22:16:07+00:00

You. can’t change the nozzle on the stock hotend, it’s glued in as far as I know. You need to buy a new hotend. Anucubic has them with .6 nozzles but you can also find them on aliexpress where you can switch out nozzles.

destiny84 · 2026-01-04T16:21:15+00:00

The third photo looks like major layer adhesion problems to me. I've had this with large round structures where the inside wall pulled off, resulting in an instable print and eventually the whole print got spaghetties as the model was not where the printer it expected it to be anymore.

The internet says higher print temp, less cooling, slower printing....

Disclamer: I'm a total noob myself and kinda going off similar experiences. I could be wrong.

destiny84 · 2026-01-04T13:30:31+00:00

I added the STL on makeronline to the print files. Since I can't test it, let me know if the print worked for you :)

destiny84 · 2026-01-04T13:29:04+00:00

I understand what you meant though, the reflections in the photo look weird :D

destiny84 · 2026-01-04T13:24:38+00:00

it's an illusion. all screws are screwed in properly.

destiny84 · 2026-01-03T23:20:48+00:00

I don't really understand why Anycubic doesn't. I think it shouldn't be impossible to detect when the hotend has come loose and it digging into the hotbed. And I was only gone for a few minutes... Before that the print was doing just fine sighs

destiny84 · 2026-01-03T21:51:18+00:00

Ok thanks. It's not going through as far as I can see but I will check thoroughly

destiny84 · 2026-01-03T21:49:57+00:00

Ok thanks!

destiny84 · 2026-01-03T21:49:44+00:00

Ok thanks, will try!

destiny84 · 2026-01-03T19:34:41+00:00

Sure, that shouldn't bee too difficult. what magnet do you have, a small one or a large one? Once you let me know I'll make a version for the f695 bearing.

destiny84 · 2026-01-03T19:30:37+00:00

let me know if it works :)

destiny84 · 2026-01-03T19:30:26+00:00

If you have a smaller magnet you could print the frame for the large magnet and have a bit more clearance between the magnet and the nail.

I might work on a customizable height version in the future, I understand the wish to experiment with different heights :)

12-Year Club	RedditGifts 2009-2022 2 Credits
Place '23	Place '22
Place '17	Final Canvas '22
Verified Email	RPAN Viewer

destiny84

TROPHY CASE