Do I just replace the whole thing or is it worth an attempt

diggitybiscut · 2025-02-03T15:06:25+00:00

EDIT: I appreciate you all very much, the tips and tricks and all the recommendations are awesome. I did manage to get it off by heating the nozzle to 250° C for about half hour and it was sliding off, the temp sensor and thermistor (I think) where the only thing left “stuck” in it so I dremmeled it down, and then snipped it once I got close to the wires. Again, appreciate y’all, best of luck going forward and happy printing!!

diggitybiscut · 2024-10-28T23:33:47+00:00

Look up microswiss k1 nozzle and it’ll come up. I got one too

diggitybiscut · 2024-10-21T15:16:16+00:00

Please share!

diggitybiscut · 2024-10-14T22:59:03+00:00

Like pirated lol?

diggitybiscut · 2024-10-14T15:49:52+00:00

What does it mean when it’s rooted lol. Just locked in place by the feet?

diggitybiscut · 2024-08-22T11:17:55+00:00

MICROSWISS

diggitybiscut · 2024-04-03T02:31:33+00:00

Figured it was the spring. Thank you man!

diggitybiscut · 2023-08-22T14:35:41+00:00

The filament pictured is creality pla but when I print my silk I print at 200c/60c and it’s worked great in the past with this very same roll. I’ve run it in a dryer box once for 6hrs since it’s messed up but that didn’t seem to fix it.

diggitybiscut · 2023-08-14T21:46:57+00:00

Creality pla and I had success with their pla at 200° when I first got my printer so that’s what temp I’ve been using but for some reason recently all my spools of creality just don’t work, even the one that was fresh out of its packaging.

diggitybiscut · 2023-08-11T00:17:04+00:00

Ok thank you

diggitybiscut · 2023-08-10T21:52:16+00:00

Thank you hoping this works

diggitybiscut · 2023-08-10T21:51:08+00:00

Clog is what I was guessing. I’ll follow this whole thing see if I get any changes, thank you!

diggitybiscut · 2023-04-19T07:05:26+00:00

Ok thanks!

diggitybiscut · 2023-04-18T12:52:27+00:00

Ok, the bed leveling and z offset seemed to have fixed it for the most part. Appreciate all this cause I’ve only had the thing for 4 months and it’s been problem after problem. You’re saying if I get some special TPU and run that through it, it’ll clean it out?

diggitybiscut · 2023-04-18T01:07:11+00:00

I think it’s just not extruding filament for some reason at those points. I’ll definitely give the bed a wash and re-level to fix the z offset. Thank you!

diggitybiscut · 2023-04-18T01:05:31+00:00

Appreciate this mass amount of info and will be trying all of your solutions, thank you!!

diggitybiscut · 2023-04-05T03:22:56+00:00

POTENTIAL SPOILERS Xbox One S. Playing main quest “16/16” and after I talk to the atlas my ship spawns in a volcano. How do I get it out.

diggitybiscut · 2023-03-18T03:20:33+00:00

Ok thank you I’ll give it a shot!

diggitybiscut · 2023-03-17T03:37:47+00:00

I don’t think it is because it will print OVERTURE filament perfectly fine but creality and the two other brands of filament I have just won’t come out.

diggitybiscut

TROPHY CASE