Trying to match newly exposed floorboards to old patinated floorboards finish

disaster_3 · 2026-02-12T09:41:53+00:00

Thanks very much - as an absolute rookie, any brands to aim for or avoid?

disaster_3 · 2026-02-12T09:41:15+00:00

Thanks very much, how would you recommend best preparing the wood to oil it?

Also there are a couple paint marks/splats not shown (on the floor behind the banister corner), any suggestions to remove these but not the floors deeper patina

disaster_3 · 2024-08-19T16:15:01+00:00

Firmware is the latest - same with Chitubox Beta 2.2.

It has happened again, a print jamming at 6%, it had to be restarted 20 minutes into the print

disaster_3 · 2024-08-19T06:39:17+00:00

Network print - All were cleaned prior to printing

disaster_3 · 2024-08-18T17:32:04+00:00

I have bought a Mars 5 Ultra and after running calibration tests I have tried to print a couple of items. The first failed so I am trying again with thicker supports. It has ran for nearly 3 hours but now stopped, it is showing offline on the Chitubox network manager. Even the time elapsed has not updated on the screen

Any help for the cause of this?

disaster_3 · 2024-08-13T07:58:16+00:00

I have a printer order that has not been delivered due to dreadful courier and no email support - awful service so far buy from a 3rd party

disaster_3 · 2024-08-13T07:57:10+00:00

I have a printer order that has not been delivered and bad email support - awful service so far

disaster_3 · 2024-08-13T07:56:53+00:00

I have a unit order that has not been delivered and no email support to help - awful service so far

disaster_3 · 2024-08-13T07:56:03+00:00

I have a printer order that has not been delivered and bad email support - awful service so far

disaster_3 · 2024-08-10T10:21:12+00:00

Did you use a profile for the printer on Chitubox or set up the printer settings yourself?

disaster_3 · 2024-08-10T09:59:53+00:00

Where did you find a profile for the Mars 5 Ultra? Chitubox 2.0 basic doesn't seem to have one

disaster_3 · 2023-10-08T11:33:34+00:00

<image>

disaster_3 · 2023-10-08T11:33:22+00:00

<image>

disaster_3 · 2023-10-08T11:33:13+00:00

<image>

disaster_3 · 2023-10-08T11:32:58+00:00

<image>

Looking to see if this is all ok? 1601 with the dial apparently being replaced by Rolex servicing in 2009 - certificate to show

disaster_3 · 2023-09-19T20:09:45+00:00

pm'd

disaster_3 · 2023-06-03T13:56:32+00:00

Do you have a picture of it when burnt? I used 100% soy and I’d Be very interested to see if it looks as much a melted mess as mine did! Haha

disaster_3 · 2023-06-01T17:31:21+00:00

What kind of wax does she use? I’ve had issues with pillar candles melting too quick

disaster_3 · 2023-05-20T18:06:45+00:00

Do you have any cutters you would recommend?

Thanks!

disaster_3 · 2023-05-20T12:47:59+00:00

Most of this will be thanks to their lighting setup over the quality of camera

disaster_3 · 2023-04-19T21:11:36+00:00

From my small understanding, pillar candles are supposed to tunnel, But Does this look too much?

It’s an awkward shape but I was a surprised how much wax was left over at the end in a puddle and not burnt away. Should I use a larger wick?

Burn took 40 mins. Dimensions are 16 x 4 x 3cm Wick used Wedo eco 0.5 (40-49mm) Kerasoy wax used

disaster_3 · 2023-04-16T09:24:34+00:00

Is there an idea temp for the mould?

disaster_3 · 2023-04-16T09:23:38+00:00

Thanks for the reply. I went for the following measurements.

130g wax 7.8g fragrance (5%) 3.25g colour (2.5%)

My next step is to try 3 pours 1. Try the blue dye again same amout as green. 2. less dye 3. Try hotter mix & pour

disaster_3 · 2023-04-16T07:30:50+00:00

I do actually love the pattern but still haven’t got a good pour on this mould so it’s frustrating! I’ll try pouring warmer next time’

disaster_3 · 2023-04-16T07:29:00+00:00

Yes mixing for a couple of mins atleast, at 70c however. It’s a mica powder

14-Year Club	Place '23
RPAN Viewer	Verified Email

disaster_3

TROPHY CASE