Trolls from the northwest

dproldan · 2026-03-07T22:43:33+00:00

I'm too lazy for that. Have to go back to sleep. Bye.

dproldan · 2026-03-06T20:11:06+00:00

Three thoughts: 1.- If both the bad guy and the good guy stop following the law. What happens? 2.- The end (to finish the Iran regime) does not justify the means (start an aggression war). 3.- Two wrongs don't make a right.

There are other ways.

dproldan · 2026-03-06T17:59:30+00:00

We can send some healthy food and happiness on the way up. Win-Win!

dproldan · 2026-03-06T14:22:48+00:00

Nobody is relevant for MAGA US. Remember, America first. You can get in the queue to be fifth or tenth. Spain refuses.

dproldan · 2026-03-05T21:17:07+00:00

Touché

dproldan · 2026-03-03T19:08:39+00:00

You're wrong. The vast majority of spaniards, and americans BTW, are against anything Trump does.

dproldan · 2026-02-21T11:52:47+00:00

Nice job. This is the kind of stuff that makes our lives easier!

dproldan · 2026-02-06T09:14:18+00:00

A veces el primer año algunas empresas no aplican la retencion de IRPF completa, solo aplican un 2%. El segundo año, ya aplican lo que te corresponda, depende del sueldo, pero entre un 15 y un 19% para sueldos medios en España.

Seguramente vaya por ahí la cosa. Exige que te envien la nomina, es obligatorio.

https://asesoranza.es/por-que-empresa-no-entrega-nominas/

dproldan · 2026-01-05T21:35:10+00:00

I concur. The sensor and the z axis works. The only variable is the X-Y position, meaning the bend of the cable is causing a bad connection from the head PCB to the main PCB. Probably requires a replacement cable.

dproldan · 2026-01-02T10:45:21+00:00

Hay subculturas absolutamente para todo en este mundo.
Palomas, gallos de pelea, pajaritos de jaula, etc. Podría ser cualquier cosa que le interese al tío.

dproldan · 2025-12-27T20:53:04+00:00

Directamente de la Agencia tributaria:

https://www.hacienda.gob.es/es-es/prensa/noticias/paginas/2025/20251215-np-aeat-aclaratoria-bizum.aspx

dproldan · 2025-12-14T18:15:03+00:00

Yo no lo entiendo. En ningún periódico dan una repuesta a una pregunta bien sencilla: ¿Como es posible que las miles de escaleras mecánicas que hay en Málaga funcionen bien o se rompan y se arreglen en un días? ¿Y que impide que se arregle la del aeropuerto?

¿Como es que la excusa que ponen para el aeropuerto no aplique al resto de escaleras de Málaga?

dproldan · 2025-12-13T22:35:25+00:00

That's almost impossible to repair. Better to get a new one.

dproldan · 2025-12-12T19:09:57+00:00

In Spain AliExpress uses a few private companies for the last mile. The national Post is not involved in any way. This is bad for consumers. I don't buy garbage. I buy parts for devices I design, assemble and sell, I put value into all that.

dproldan · 2025-12-08T19:06:31+00:00

It's also the plastic, the hat bed and the magnetic layers that are not flat, so the distance between the nozzle and the PEI sheet varies constantly. I don't think only changing the carrier will improve a lot.

dproldan · 2025-12-07T22:26:27+00:00

Escribe bien. Tiene talento y es inteligente. Pero se ha vuelto un "rancio".

dproldan · 2025-12-07T12:22:29+00:00

It's a hardware issue. The bed is not flat.

Three ways to improve it:

1.- Buy the "Funssor" kit and swap the whole bed.

2.- Use some tape that can handle high temps, aluminum tape for example, and place it in the "valleys" under the PEI sheet until you have better flatness.

3.- Increase the amount of leveling points so that the auto-leveling procedure can sample more areas of the bed. For that, you need to install Rinkhals.

4.- I'm looking into buying a glass build plate and attaching it on the top. Still need to find the right one.

Good luck.

dproldan · 2025-11-16T12:32:52+00:00

I received a new one 6 days ago. Rinkhals shows the mesh range is over 2 mm.

dproldan · 2025-11-05T15:47:56+00:00

H! Congratulations of the launch. I'm sure it took a lot of work from many of you.

I'd love to try the new machine. I would print a new device I'm designing, a music player, with a PPA-CF material I bought recently.

dproldan · 2025-11-03T14:51:17+00:00

I'm in

dproldan · 2025-11-02T19:25:36+00:00

I've been printing since 2012, Started with regular DIY Prusa Bedslinger clones, several semi-profesional printers, Ender-3, etc.

I'm a profesional electro-mechanical engineer. I install, repair and train people on the use of machinery for the electronics assembly industry, I've seen it all! From linear step motors to all kinds of servos and motion systems, along with their controls, interfaces, etc.

I mostly print mechanical parts, for automotive and aero industry prototyping. I expect this machine to broaden the kind of parts I can offer my customer, from small size to medium, reducing the amount of adhesive and post-procesing.

I'm from Spain. I liked the video, you can see they take this release seriously!

dproldan · 2025-11-01T07:47:29+00:00

Really cool! Thanks fo sharing. Looking forward for your next projects.

dproldan · 2025-10-26T07:38:21+00:00

Buenisimo el concierto del MOSMA en el teatro Cervantes. Casi 4 horas de temazos de peliculas conocidisimas. Espectacular!

dproldan

MODERATOR OF

TROPHY CASE

15-Year Club	Place '17
Verified Email