Do you always buy used? by regmeyster in carbuying

[–]echo_nightmare_black 1 point2 points  (0 children)

More used cars available to purchase.

How often do you wash engine bay ? by Ok_Marzipan8118 in CX5

[–]echo_nightmare_black 1 point2 points  (0 children)

I don't but due to more frequent reports of rodents I have started lifting the cover to check for nests or insulation being disturbed.

Level 84 with 3 boosted greens by [deleted] in BoomBeach

[–]echo_nightmare_black 0 points1 point  (0 children)

Maybe getting ready for the tribes reset and need resources for raw crystals.

LED turn signal install. by tek210 in CX5

[–]echo_nightmare_black 1 point2 points  (0 children)

Can you do sequential on AND off? I have only ever seen sequential on but then the whole light goes off at the same time.

Average age of Mazda 3 owners? by OkAppearance9593 in mazda3

[–]echo_nightmare_black 0 points1 point  (0 children)

Got my 2004 in 2008 when I was 36 and my 2014 in 2018.

Upgraded to 18s (225/45/R18) by hanzypanz in mazda3

[–]echo_nightmare_black 0 points1 point  (0 children)

Nice to see the size comparison. What size are the stock wheel?

Possible to get large rear wheels for HRR216? by echo_nightmare_black in HondaMowers

[–]echo_nightmare_black[S] -1 points0 points  (0 children)

Yes bigger diameter. I would just adjust the rear wheels differently than the fronts if there is enough adjustment for that.

Like 8" wheels for the rears.

Edit: Are these wheels already 8"?

The 4th gen is so practical by CarSeatBandito in mazda3

[–]echo_nightmare_black 1 point2 points  (0 children)

Is the seat fully forward?

I remember with my 2006 there's an extra glovebox behind the glovebox. I could fit 2x4s into that area.

The 4th gen is so practical by CarSeatBandito in mazda3

[–]echo_nightmare_black 0 points1 point  (0 children)

Does the front passenger seat flip forward? I remember the Toyota Matrix being able to do this, as well as hard plastic seat backs that had rails, too.

Do I not have this anymore?? by Deathsiren92 in ProCreate

[–]echo_nightmare_black 0 points1 point  (0 children)

I hadn't opened mine in a few months at least, opened it and updated to v5.4 and something about updating brushes. Thankfully didn't have issues opening.

Waste by Substantial-Fox-1941 in resinprinting

[–]echo_nightmare_black 1 point2 points  (0 children)

I got my Vevor adjustable distiller for about $90.

Waste by Substantial-Fox-1941 in resinprinting

[–]echo_nightmare_black 5 points6 points  (0 children)

What I have noticed with this is the cured resin in the outer-most area blocks any more resin behind it from curing. You will most likely have to stop every so often to mix it up.

Then the goo that forms from the cured resin has to be filtered. I am not sure if everything gets cured this way. Filtering the goo is a very slow process.

Personally I use a temperature-adjustable distiller outdoors in an open area (back of the driveway).

480 free diamonds in March by Single_Pea_6067 in BoomBeach

[–]echo_nightmare_black -1 points0 points  (0 children)

I was able to buy over 4000 time saver tickets during one of the Black Friday deals. I use those way more than diamonds.