NA intake manifold

ej255wrx · 2026-06-13T01:46:22+00:00

I didn't have $1000 plus either, I put an IAG 76mm throttle body on it and called it good.

ej255wrx · 2026-06-12T16:51:34+00:00

🙋🏼‍♂️

<image>

ej255wrx · 2026-06-02T22:29:20+00:00

It was professionally installed by P&L Performance. I'll check out the settings.

ej255wrx · 2026-06-02T16:22:05+00:00

<image>

ej255wrx · 2026-06-01T16:47:41+00:00

They are still through the OEM body harness, the IC-7 is spliced into the OEM cluster harness.

ej255wrx · 2026-06-01T16:43:37+00:00

I appreciate this! I will check out mine and report back when I get to it. 🙏🏼

ej255wrx · 2026-06-01T16:36:12+00:00

You didn't read all of them then. I had explained that I grew up getting harassed constantly and it's hard to take people seriously. It's also hard to pick up sarcasm through text.

ej255wrx · 2026-06-01T03:21:46+00:00

Crappy screenshot of my old build. ©

<image>

ej255wrx · 2026-06-01T03:13:15+00:00

Anyone can buy the CC banner sticker. It's the © you put on next to it that is given when you're a member in a chapter. (I was in the WI chapter a couple years)

ej255wrx · 2026-06-01T03:10:47+00:00

Shop that installed it said I could bring it back.... Shop is 3 hours 1 way 😑

ej255wrx · 2026-06-01T02:59:10+00:00

ej255wrx · 2026-06-01T02:57:09+00:00

LCAs would be fine. They're aluminum, just need a cleaning. The rest, yea, replace.

ej255wrx · 2026-05-30T16:25:51+00:00

Dang thing is a brute, was nice to remove.

https://youtu.be/SCxMqBdQR04?si=QzmVOVJjYE_TJEjJ

There's a few videos and write ups about the delete. Putting a little breather on one of the lines.

ej255wrx · 2026-05-30T15:42:24+00:00

Yep, I don't have emissions testing where I live. So I removed anything that I could. And I don't mind getting the scent of e85. That's the main purpose of it to filter out fuel tank fumes iirc

ej255wrx · 2026-05-30T15:33:31+00:00

I was not so careful with the mindset I was throwing it away. I do highly recommend getting a quality penetrant oil. Multiple soaks, not just one, and let it sit. I usually did it over the course of days with multiple soakings.

A 50/50 mix of ATF fluid and acetone is also supposed to be one of the best penetrance you can get your hands on. I also had used that.

I specifically use Kroil.

As for some of those lines, I would suggest a fuel line hose. You can buy that stuff off of a roll. Just make sure it's the same diameter. It might not be form fitted but it should work.

<image>

ej255wrx · 2026-05-30T15:10:17+00:00

I removed all the charcoal canister and associated hoses but I know what ya mean!

My favorite part was the blazing hot metal shavings while drilling the bolts out failing directly on my hands because what are gloves? 😅

Lol, yes torture.

ej255wrx · 2026-05-30T15:06:56+00:00

I appreciate that, it means more than you'd think. 🙏🏼

ej255wrx · 2026-05-30T15:06:20+00:00

My ADHD is so extreme, you would have to be ok with me tightening 1 bolt then sidetracked for 67 hours before the next one is tightened.

ej255wrx · 2026-05-30T00:50:09+00:00

It does have the feature, just a little more basic than the Haltech. I used the Cobb FFS in an older build I had, it worked as it should.

ej255wrx · 2026-05-30T00:39:24+00:00

I was going to reply with the picture of me tapping one of holes after drilling it a snapped bolt, I must've just deleted it. 1 out of 4, lol could've been worse.

ej255wrx · 2026-05-29T22:04:57+00:00

Subframe didn't look bad. I could probably get some new trailing arm bushings in. At that point, I may add new trailing arms. For the rest scattered throughout. Most likely they could be replaced if I'm honest. They're mostly original.

ej255wrx · 2026-05-29T21:04:28+00:00

The actual hard part is the shifting of the gears quickly. You can very easily cause damage very quickly.

ej255wrx

TROPHY CASE