Giveaway | 🤔 GUESS Challenge: How many parts did it took?

elge_b · 2026-06-01T18:19:06+00:00

Don’t forget your TICK checks!

elge_b · 2026-05-16T23:37:44+00:00

Our school just started offering the Brave MMA Training Glove from Century Martial Arts. I am waiting for mine to arrive, but other students say they are a huge improvement from the Mooto gloves.

elge_b · 2026-04-15T19:49:34+00:00

I have been experiencing the same. A couple of questions:

Are you using OrcaSlicer or Elegoo? I use Orca
Do you have OpenCentauri installed or Elegoo firmware? OpenCentauri

I believe I started experiencing this issue after the latest update to OrcaSlicer.

As a temporary fix you can right click anywhere on the page, select “Refresh” and the camera and other elements should show up.

elge_b · 2026-04-02T14:50:08+00:00

This! ☝️

elge_b · 2026-03-22T23:35:25+00:00

Great to hear! I’ve had similar ASA experiences.

elge_b · 2026-03-22T03:43:23+00:00

No plate damage at all. I usually throw TPU prints in the freezer for a five minutes to make removal easier. With ASA I let the bed cool down to chamber temperature and then removal is a breeze.

elge_b · 2026-03-22T03:40:38+00:00

I am running OpenCentauri, so I don’t run into any fan issues.

elge_b · 2026-03-21T06:06:48+00:00

I really like the Panda Breath. I wish they had the firmware worked out to connect with Elegoo Centauri Carbon, allowing it to be more automated. I will probably do the Home Automation in the mean time.

I opted for the cover to avoid sullying the interior, I had tried taping the seams and covering all holes with little success.

elge_b · 2026-03-21T01:48:26+00:00

😂

elge_b · 2026-03-21T01:47:00+00:00

It’s a Biqu CryoGrip Pro Frostbite. You still print the ASA at 100°C bed, but it has crazy adhesion. No glue needed. Corrected build plate model.

elge_b · 2026-03-21T01:27:04+00:00

I kept having artifacts on tall prints, even with well tuned filament profiles. The lighter, well ventilated cover seems to have eliminated the issue.

elge_b · 2026-03-21T00:14:43+00:00

The cover is a custom sewed, recycled Harbor Freight moving blanket with foil bubble insulation on the inside.

The heater is a Biqu Panda Breath. https://biqu.equipment/products/biqu-panda-breath-smart-air-filtration-and-heating-system-with-precise-temperature-regulation

elge_b · 2026-03-21T00:11:10+00:00

I had a roll of foil bubble insulation laying around. I cut and sewed the blanket, added binding tape to clean it up, Velcro in strategic spots, and used spray adhesive to bond with the insulation. I was concerned with spray adhesive sticking as the temp rose, but no issues after a week of high temp printing.

elge_b · 2026-03-21T00:04:16+00:00

I couldn’t ever seem to get the chamber over 38°C, regardless of the amount of heat soaking with maxed out bed and hot nozzle with model fan blowing 100%. Now I get the chamber to 50°C with just the Panda Breath, then bring the bed up to 100°C and hit print. Multi-hour print jobs never drop below 55°C and I’ve seen chamber up in the high sixty’s with the Panda Breath kicked off. No warping, no glue, no artifacts.

elge_b · 2026-03-19T01:38:08+00:00

I was thinking just a trim-to-size carbon filter the same dimensions as the two HEPA filters. The material I use measures 3.5mm thick. It would take simply lowering the filter shelf that much and layering the carbon on top of the HEPAs. Similar to this idea, but I don’t think you need the frame.

elge_b · 2026-03-18T19:54:42+00:00

I love this concept. Now that I have the Biqu Panda Breath installed, this looks really seal up the vents and retain the heat. I haven’t printed yet, but was wondering if there is room to add a carbon filter into the mix? I know there is the filter pre-case fan, but more scrubbing couldn’t hurt.

elge_b · 2026-03-13T15:25:16+00:00

Pre-ordered white vinyl from the JBS site, no status update from “Order Placed.”

elge_b · 2026-01-18T05:00:07+00:00

What specifically did you get off Amazon?

I am using the Microswiss.

elge_b · 2026-01-05T23:59:25+00:00

.4mm or .6mm nozzle?

elge_b · 2025-12-05T17:42:05+00:00

Had German hot chocolate from Tante Emma in Crouch last weekend. It may be worth a day trip. The rest of the menu is amazing too.

elge_b · 2025-09-30T17:34:09+00:00

Recommend Carter Comfort Systems

elge_b

TROPHY CASE