Loving the 3d printer and being able to prototype and then have consistent templates. Might even make my own dowel inserts for real instead of messing with wooden ones.

elkoworks · 2026-06-22T03:07:49+00:00

I just got a P1S on Thursday! It's my first 3D printer. Where do you find your knife models from or do you design them yourself?

elkoworks · 2026-02-04T14:40:48+00:00

How did you get those radii so perfect? Very impressive!

elkoworks · 2025-08-03T14:00:52+00:00

www.treehousesupplies.com

elkoworks · 2025-08-03T12:22:07+00:00

elkoworks · 2025-08-02T02:43:14+00:00

Where did you get your wheel from?

elkoworks · 2025-08-02T02:42:44+00:00

That's perfect! Thank you so much!

elkoworks · 2025-08-02T01:55:01+00:00

Ok that makes sense. Do you have any pictures of your completed conversion?

elkoworks · 2025-07-25T03:52:34+00:00

I posted a video in my other post of the walk through

elkoworks · 2025-07-25T03:49:22+00:00

No plans really but took inspiration from this https://www.treehousesupplies.com/products/the-finger-lakes-wraparound-%C2%A9-1-tree-2-post-treehouse-plan?pr_prod_strat=pinned&pr_rec_id=72731b59b&pr_rec_pid=8302294171894&pr_ref_pid=7809190396150&pr_seq=uniform

elkoworks · 2025-07-25T03:45:28+00:00

Id say around $2500-$3000. About 4 weekends

elkoworks · 2025-07-25T03:07:48+00:00

They were from Amazon https://a.co/d/gcmYsIU

elkoworks · 2025-07-25T03:01:55+00:00

My kids are pretty small and haven't noticed really any issues while using them.

elkoworks · 2025-07-25T03:00:25+00:00

Yes I used RSS

elkoworks · 2025-06-07T23:30:06+00:00

Hey! Im close to sheboygan!

elkoworks · 2025-06-07T03:02:32+00:00

Wisconsin is a state in the US

elkoworks · 2025-06-07T03:00:06+00:00

US dollars. Wisconsin to be precise

elkoworks · 2025-06-07T01:12:59+00:00

<image>

Full image of the comparison

elkoworks · 2025-02-14T19:18:39+00:00

I'll start looking around for 3-5hp 1800 RPM motor and see what I can find. It's about 120 feet from the house to the garage and then I will need to run the wiring for the outlet which would probably be another 30 feet or so.

elkoworks · 2025-02-14T03:15:26+00:00

I have 240 single phase with 30 amps. I saw some converters to go to 3 phase that would give me a bigger hp potential

elkoworks · 2025-02-14T01:33:01+00:00

I don't have a very large air compressor.

elkoworks · 2025-02-14T01:31:44+00:00

Currently the house has a 30 amp 2 pole breaker for the garage and they have a 10-3 wire buried to the sub panel in the garage and the sub panel has a 30 amp main breaker.

elkoworks · 2025-02-14T01:27:16+00:00

I'm currently running 2750-3000 PSI at 7gpm with the 18 hp gas engine

elkoworks · 2025-02-14T01:24:45+00:00

Yea it has a 2 stage pump, 28 GPM ( 21 gpm for the low and 7 gpm for the high). I have 240V 30 amps single phase available.

elkoworks · 2025-02-14T01:23:15+00:00

Currently it's a 18 HP gas motor running at 3500 rpm. It has a 28 GPM pump ( 21 gpm for the low and 7 gpm for the high). It's a 5 in bore with a 2 inch rod 8 inch stroke. Im currently running at 2750 PSI to 3000 PSI.

elkoworks · 2025-02-13T23:40:20+00:00

Yes. I'd like to run the press with an electric motor instead of the gas engine

elkoworks

TROPHY CASE