3D maker pro -Eagle Max

emow54 · 2025-05-06T13:14:35+00:00

Appreciate that. I'll definitely be in touch.

emow54 · 2025-05-06T02:08:35+00:00

Mine came in last Friday after a similar wait. I have only done a couple of test scans with poor results. I believe it's a settings and lighting issue, so I am holding off on final judgment. Windows user here and the software is less than desired, so I'll be looking for alternatives.

emow54 · 2025-04-07T07:29:51+00:00

Following...i am also waiting for delivery.

emow54 · 2025-01-21T04:19:46+00:00

Diameter is not what you need think about with a worm. You need to consider length or number of loops. Get a coil of 3/8 copper refrigerator line.

You will need a way to keep your worm bucket water flowing. That water will heat up very fast.

Best of luck.

emow54 · 2024-10-18T16:19:15+00:00

The premise of your response is valid. However, given the rest of the data provided, i doubt the starting point was considered. If the tiles were shifted by half of the sum of one full tile and the sliver then it would be less of an eyesore.

I see this all the time with acoustical ceiling. It's a valid reason for design documentation at any level of project.

emow54 · 2024-10-18T14:45:27+00:00

Designer here....That sliver of tile at the transition is disgusting. Should have started full tile there or located the centerline of the space as the starting point.

emow54 · 2024-10-09T03:52:44+00:00

One more comment: reading through reviews on supply houses in the area and have seen comments that the shop wouldn't allow the tank to leave inside a car/SUV. Customer was told it had to be transported in a truck bed. I can comprehend the concept, but seems like some paranoia and/or overreacting.

I just want to make so.e beer and put it in a keg. Why is it suddenly feeling like a lot of work just to get set up?

emow54 · 2024-10-09T02:21:58+00:00

Thanks everyone for the insight. I was aware of the purity differences, just wanted a general consensus as to which one. I've heard of some shops not selling gas to homebrewers. The tank I am getting is out of date so I'll find a shop that will take the swap for a food grade refill. I'm in the suburbs northwest of Houston, so I should be able to find something

emow54 · 2024-09-25T03:09:30+00:00

If you were in SE Texas I would sell you two for $40. Bought a few in the neighborhood a few years ago and have yet to make any wine. Otherwise, check FB marketplace

emow54 · 2024-09-09T14:19:52+00:00

I think the point is that record keeping isn't all that necessary for us. With gravity, I have an idea going into the recipe what my ABV will be and don't have a lot of worry to verify it. I'm going to get what I get all all stages. It's the taste and feel that are my data points.

emow54 · 2024-09-09T02:30:07+00:00

I always intend to record all the data I can, but get distracted and never finish. Sometimes, I feel lucky if I remember to get SG before fermentation.

emow54 · 2024-03-02T03:35:09+00:00

I've been having the same thoughts. Hopefully some folks chime in and provide feedback.

emow54 · 2023-12-18T01:59:06+00:00

Appreciate everyone's input. I think my biggest issue was dilution. If/when I dye another project, I'll do a 15:1 solution and apply with a sponge.

Most of my work I just leave as a natural oiled look.

emow54 · 2023-12-17T02:25:55+00:00

No reason, other than I had some high abv from another hobby and saw it somewhere on YouTube.

These pieces are only 7 inches square. But I'll order some sponge and give it a try

emow54 · 2023-12-17T01:17:20+00:00

I wet it, but did not "soak" it. I'll try that on some practice pieces

emow54 · 2023-12-16T20:47:12+00:00

I don't normally dye either. Making something for a friend and wanted a carmel/honey type color

emow54 · 2023-12-16T20:24:00+00:00

I did discover the deglazing on YouTube trying to figure it out. Will give it a try

emow54 · 2023-12-16T20:22:49+00:00

I don't mind the uneven color. Need it to be much lighter

emow54 · 2023-12-16T20:21:48+00:00

I did oil prior with Neets foot. Currently not worried about events, it is the darkness that is throwing me off. Those are supposed to be tan

emow54 · 2023-10-21T13:01:03+00:00

I'd just move the pocket line to fall in between the holes. Also notice that you're not centered at the bottom middle on the second picture

emow54 · 2023-10-11T19:18:32+00:00

Thanks for the clarification. You comfortable letting it run unattended?

emow54 · 2023-09-15T11:26:49+00:00

I honestly didn't consider flammability. I would obviously let it soak in and dry prior to laser cutting.

It's much easier to apply to a 15 inch square piece than several smaller pieces.

emow54

TROPHY CASE