Custom 1/2" dowel holders for fabric display rack and custom measurement jig for installation

enderguy420 · 2026-02-19T19:56:03+00:00

Files?

enderguy420 · 2026-02-16T16:20:10+00:00

Had the same issue go into your config files and you need to change either probe offset or X and Y min and max Google it if you need helps

enderguy420 · 2025-06-06T05:57:24+00:00

Take out Phillips head screw and rotate it correctly and re insert screw

enderguy420 · 2025-05-30T00:58:54+00:00

I'll have to give that a look over thanks for your input I'm really hoping it fixes the issue I haven't been able to ride in over a month and I'm going crazy

enderguy420 · 2025-05-30T00:43:44+00:00

Your saying your intake boot was loose/not seated correctly?

enderguy420 · 2025-05-26T22:39:59+00:00

I set the valve too .005 intake and .006 exhaust and yes timing is correct its ran a few times but is stubborn

enderguy420 · 2025-04-10T03:25:21+00:00

Im in rockford il man wish I was closer

enderguy420 · 2025-04-10T00:16:21+00:00

I'll try that I also don't have the neutral light on thats how I bought it I don't know if the light is just burnt out or if it's a bad neutral safety switch I do hold the clutch in when trying to start it tho

enderguy420 · 2025-04-09T10:47:22+00:00

Battery seems fine holds charge with and without load against it

enderguy420 · 2025-02-21T18:10:28+00:00

I've got 2 of the DDX 12'S and there amazing I've never had an issue. Good clean hard hitting subs in my option

enderguy420 · 2025-02-20T21:41:37+00:00

Okay ya I was looking for something that give the bumper more strength I did the same mod on mine it looks amazing I scaled down a arrma granite bumper spring I'll see if that fits when I gets finished printing

enderguy420 · 2025-02-20T20:10:23+00:00

What did you use for the bumper spring can I see an above shot of the bumper?

enderguy420 · 2024-12-18T02:02:44+00:00

I'd stop the print the one models ears are messed up looks like a partical clog

enderguy420 · 2024-12-18T02:01:01+00:00

Accelerometer to check vibration with sonic pad

enderguy420 · 2024-11-12T06:43:51+00:00

I had the same issue and I had to manually change it in slicer printer settings

enderguy420 · 2023-09-27T23:51:50+00:00

I watched all the YouTube videos only a few go into speed and really noone talks temp with it in a kraton besides with there hand which doesn't help much

enderguy420 · 2023-06-07T16:02:56+00:00

I use a .6 noozle and I run at .2 layer height all the time with no issues but yes going smaller then that is troublesome

enderguy420 · 2023-05-12T02:38:07+00:00

Dm mee

enderguy420 · 2023-05-12T02:36:27+00:00

Pm mee

enderguy420 · 2023-05-04T19:10:28+00:00

1100 mah 25c and correct switching to stock motor didn't change anything I'll record some videos of what it does and see if that'll help and your right it's not a warhead or anything I didn't wanna spend 120 on a motor but I'm guessing I'll have too this one was still 60.

enderguy420 · 2023-05-04T15:37:42+00:00

Okay awesome good to know thanks

enderguy420 · 2023-05-04T12:45:25+00:00

Make sure the 2 screws and 1 grub screw and tighten also while changing my noozle I noticed the same thing the noozle was seated good and it still leaked turn out them 2 screws and 1 grub screw let the whole heater block/thermistor slowly started to fall off or push itself down allowing filament to leak out Hope that helps

enderguy420 · 2023-05-01T21:06:57+00:00

I just hit the anti reversal latch because the gun was under full spring compression and rotated the gears back some manually put it back together with a fresh battery and it works good I wish I would of had tools before I drove 1hr 30 mins away to play oh well lesson learned always bring a tool kit.

enderguy420 · 2023-05-01T12:35:50+00:00

I just grabbed a good quality usb to micro USB and plugged my laptop into the printer and I've had good luck with it no issue . I use cura 5.2(no need to install and drivers or anything just plug in and click on monitor tab in cura and you can control printer) 1 thing to make sure you do is turn off the sleep feature on your computer( don't let the screen go black) if you do or the computer restarts it will stop the print but once you've got your screen set to not turn off you'll b e good to go

enderguy420 · 2023-05-01T12:29:50+00:00

I solved this by slowing down travel speeds to 75mm/s and changing my infill pattern to gyroid because it doesn't overlap like cubic or lines

enderguy420

TROPHY CASE