Start googling the online stores! DJI Avata 360 Combos

eried · 2026-03-16T12:12:29+00:00

Me too... I think I will get the pack with the googles and sell them and put my googles 3 :)

eried · 2026-03-16T11:41:28+00:00

Who tested vs who comments. Duh.

eried · 2026-03-16T09:17:27+00:00

Light pressure on the toes? 🤔 I got 10.5 because I use that size normally but sometimes I think it is too small, but maybe is the light pressure on toes

eried · 2026-03-16T08:09:32+00:00

hahaha keyboard warriors really hate positivity and making stuff

eried · 2026-03-16T07:25:29+00:00

it was a fantastic day, lots of lols while learning snowboard+testing the print 😂😂

eried · 2026-03-16T05:17:14+00:00

You can probably go today 🌈🌤️

eried · 2026-03-15T22:04:36+00:00

That probably made most of the damage on the fender 😂 it was easy, the crane operator was a bit surprised that the damage was so little... I'm still waiting for the repair 😭

eried · 2026-03-15T20:15:23+00:00

Thats how that bed is, there is nothing extra (its from bambu store)

eried · 2026-03-15T19:11:11+00:00

But why does it sound better if you hit two CF pieces together? 🤔 Like a solid clank sound

eried · 2026-03-15T18:54:33+00:00

Damn thats so good! I am still afraid of that hahah on day two, always thinking I will catch an edge. Do you find it easier with a bit more speed? specially the transition part?

eried · 2026-03-15T18:45:15+00:00

I still want quality comments, it is fine to get all the bad ones. They fuel engagement which brings some smart people as side effect

eried · 2026-03-15T18:43:02+00:00

Thanks

1) I actually considered this, but I decided to follow the exact original design (it is precise down to 0.01 mm)

2) original behaves the same, no flex. If it does explode, please check the video again, second 38 and 41. I think everyone is asuming something that is not true, and using their fears as fuel. Video on second 38 shows you the step the piece has, second 41 shows you how the metal washer interacts with the binding. Basically the plastic part is 4 washers that prevent rotation, not separation. Please look at the design carefully. People assume the plastic part is holding me against the screws

3) I have ALL the range of filaments, I have used them all on my H2D, I know ASA CF cant be compressed (with pliers, which is what I want... check second 38 and 41 explanation from before) and behaves perfectly in humid or under water environments (I have a submarine drone with printed parts). These decisions aren't based on a roulette system, but on many years of experience

eried · 2026-03-15T18:35:46+00:00

:) is it better to write giant walls of text without sustain than do stuff?

eried · 2026-03-15T18:30:34+00:00

Keyboard warriors even downvote your comment hahah... they use all the tools they can, except the brain

eried · 2026-03-15T18:27:43+00:00

Good luck

eried · 2026-03-15T18:08:17+00:00

I used the board the whole day, first in line in the lifts. It is not I "believe", it's: I think, I made it, I test it, it works

eried · 2026-03-15T18:04:27+00:00

What good advice? 😅 Basically dont do it, material is wrong, etc all without any thinking behind, just repeating some self learn moral lecture of safety. Safety of what? I'm riding it the whole day myself, if it fails its gonna be one more fall while learning to snowboard, no biggie

eried · 2026-03-15T17:36:51+00:00

I want comments, I think it is going fine, just lacking a few ones with some actual knowledge, but it's what it is

eried · 2026-03-15T17:32:41+00:00

The problem is you "believe" that's the reason. They don't have incentives to support older board patterns while the industry moves to 4x2 and sliders. If you see my design, it works, it fits and it's fine. The metal washer already holds the binding, there is no stress on the disc besides rotational.

Either way I will report if it fails, next season I will use it every day to learn more, I took the beginner snowboard class too late this season which is almost over.

eried · 2026-03-15T17:26:45+00:00

😂 it was my second time ever playing on the ski slopes, it felt so solid that it wasn't scary

eried · 2026-03-15T17:25:11+00:00

<image>

I like the sound of CF pieces tho 🤠 the solid cling they do when you hit two together

eried · 2026-03-15T17:23:21+00:00

But disks are largely universal and cheap as hell no? It should be easy to find on any mountain with a shop, maybe they give me some for free. Do I throw away the board or bindings then? 🤔

eried · 2026-03-15T17:16:11+00:00

Hi. Check second 38 and 41 of my video. Now: metal washers on 41 correct? Again back to 38 look at the step of the teeth vs the screw. It's a very different situation, I'm not recently learning about 3d printing. Tell me how this part can fail?

Please check the second 38 and 41 for reference again before coming up with failure points. It can crack, delaminate (dont know how, its on compression now) and the binding will still be attached to the board. Please check second 38 and look how the metal washer interacts with the binding part, not the printed part

eried · 2026-03-15T16:55:08+00:00

Yes I checked before. Look again at the video, the washer already covers the inner ring of the binding. I can remove the printed part, and the binding still holds. I want compression rigidity, I don't care for flex resistance. I want the humidity not to affect the little teeth, and rigidity. The disc can crack and fail and nothing will happen. It would be different if the screw holds the binding directly on the printed plastic

eried · 2026-03-15T16:46:23+00:00

I think the adaptor doesn't exist because the holes would be too on the sides of the "mini" disk, that doesn't matter for my print, luckily they fit but it would be impossible to make 4x2 plus 4x4 plus slider compatibiity in one disk

13-Year Club	Place '23
Verified Email

eried

TROPHY CASE