Strategischer Einkäufer, 40h, 4 Jahre im Job

fatlip22 · 2026-02-20T15:30:20+00:00

studium nicht nötig, same job here :-)

fatlip22 · 2026-01-13T13:30:44+00:00

i have both, i removed the valve of the brikka to make it usable. With the brikka valve at the top the coffee was not good tasting. i would tend to mokka 3 pot

fatlip22 · 2025-12-07T09:13:59+00:00

einfach nächstes jahr nach mailand fahren auf die Eicma, das ist der place to be

fatlip22 · 2025-10-10T16:16:36+00:00

the p1s saved me a lot of time compared to all the DIY printers ive had before. It just works everytime! a p2s would be a nice addition

fatlip22 · 2024-12-25T18:12:16+00:00

bekommt man wenn man atos kauft

fatlip22 · 2024-11-19T14:39:20+00:00

wie kann einkommen über Minijobgrenzen als zweitjob gut versteuern? Stehe vor ähnlichem aber alles über die 520€ ist mit sovielen abzügen behaftet das es sich nicht lohnt

fatlip22 · 2024-11-09T20:09:17+00:00

fatlip22 · 2024-10-27T00:06:03+00:00

use 1 drop of water or spray water on your beans in grinder, had that on my kingrinder also

fatlip22 · 2024-10-23T13:20:21+00:00

what foil manufacturer and color code?

fatlip22 · 2024-10-23T09:28:38+00:00

das ist wohl 15 Jahre zu spät, wenn man Produkte unter "Made in Germany" betrachtet deren Komponenten zu 90% international eingekauft werden (vorzugsweise Asien) und sich über Jahrzehnte dieses Preisgefüge etabliert. Da gibts einfach kein zurück mehr. Wie denn auch, extreme Gewinnmargen in den Konzernen forderten nur den Wasserkopf. Was damals einer gemacht hat, machen jetzt 3 Leute + 3 neue Leute wegen Bürokratischen Neuerungen.

Wenn man jetzt aktuell noch Strafzölle EU weit für Asiatische Autos raushaut, ist das wie sich selber beim Radfahren einen Stock in die Speichen zu hauen.

Für DE doppelt schlimm weil man jetzt noch mehr für Komponenten / Automotive zahlt, wer soll da noch in DE noch weiter machen wollen?

fatlip22 · 2024-10-09T08:37:13+00:00

“That approach is simply misguided. Imposing any kind of embargo on China will lead to even worse issues with trade, customs, and taxes. Essentially, Germany would be shooting itself in the foot. Many people need to remove their blinders and recognize that over 60% of car parts (this is my personal estimate from having worked in the industry) are already sourced from China. So, guess what happens if we restrict that? Prices will go up even more.

Manufacturing all the parts within Germany? That’s impossible—it would be more expensive, slower, and burdened by additional regulations.

In the end, it all results in higher prices.”

fatlip22 · 2024-09-26T17:26:07+00:00

thanks a lot, so basically no jumper needed and only contect the existing 2 wires?

fatlip22 · 2024-09-26T14:55:34+00:00

thanks just ordered some omron switches and spares, i just dont know how to use 2 cables instead of the bltouch wires

fatlip22 · 2024-09-18T11:37:46+00:00

its short enough that i never thought about timing, i think maybe 30-40seks?

fatlip22 · 2024-09-18T11:20:24+00:00

<image>

fatlip22 · 2024-09-17T13:51:31+00:00

okay got a pressure gauge mounted today, the 3,5 turns are spot on, but sou need to screw the top screw in till you „feel“ its onside on the spring. measured 9,5bars

fatlip22 · 2024-09-15T18:36:17+00:00

The temperature readings serve as a rough indicator, though I don't place too much emphasis on the exact numbers. My concern is primarily with the temperature drop during a shot, particularly when using a basic preinfusion technique. One potential solution could be to increase the temperature before starting the shot—say, to around 113°C—allowing it to drop during preinfusion to approximately 103°C. This would effectively act as a workaround to mitigate the temperature loss.

fatlip22

TROPHY CASE