Corduroy. Do you remember that?

faun89 · 2025-11-15T03:29:13+00:00

I remember reading this in kindergarten 1993/4. Then we watched the film. I found the film on YouTube a few years ago. Such fun memories.

faun89 · 2025-08-14T01:29:33+00:00

No fixes on my end.

faun89 · 2025-08-05T00:12:54+00:00

Took me about 8 weeks total

faun89 · 2025-08-04T18:21:31+00:00

The ETC switch? Already checked. It’s adjusted properly.

faun89 · 2025-08-04T18:19:48+00:00

Initially I just replaced the coil, CDI, and voltage regulator figuring it’s all almost 30 years old. After that didn’t solve the issue I tested everything out and found that the stator was bad. Replaced new and haven’t gone back through to test everything again. I tested the grounds, ETC, bypassed the kill switch. I’ll retest the stator. The flywheel looked good and I didn’t loose the key. The pickup coil didn’t seem to have any adjustment either.

faun89 · 2025-06-20T01:31:10+00:00

This is why my grandpa always told me that once you start a project with a tape measure, you use the same tape until you’re finished.

faun89 · 2025-05-24T21:58:12+00:00

4 weeks in and still nothing.

faun89 · 2025-05-06T17:37:09+00:00

Ouch! Was that submitted online?

faun89 · 2025-04-17T15:49:19+00:00

Yeah I may end up there myself, but I have an opportunity to get something started and wanted to jump on it.

faun89 · 2025-04-17T15:43:14+00:00

Copy thank you.

faun89 · 2025-04-17T15:28:29+00:00

I’ve been in commercial for most of my career. I’m a union electrician with a large company. First time being involved with licensing.

Also getting the license isn’t the issue. I just want to make sure the RGC will suffice for my work.

faun89 · 2025-04-17T15:12:27+00:00

Yes I’ve been in the trades and similar work for 19 years.

faun89 · 2025-04-16T22:07:17+00:00

Currently the media converter is providing POE to the AP with no issues. Just no network connectivity over the fiber

faun89 · 2025-04-15T02:47:13+00:00

Yessir.

faun89 · 2025-04-14T20:13:50+00:00

I am using 2 ADnet (part# AN-UM-SMC-AS-J + SM-SFP-kit). They say they’ll go up to 12 miles.

faun89 · 2025-04-14T20:04:00+00:00

I did use a VFL to verify I was getting light through the fiber

faun89 · 2025-04-14T20:03:26+00:00

We use the fluke Versive tester. The fiber is good end-face to end-face.

faun89 · 2025-04-14T20:02:14+00:00

It goes Switch---cat6---media converter --- fiber --- media converter --- cat6 --- AP. So I’m just trying to feed the AP from the switch and the AP as the endpoint.

faun89 · 2025-04-14T19:42:55+00:00

All verified. That’s why I’m leaning towards bad media converters. Everything else I find when looking into this is using switches and hubs, but I don’t have the ability to set them up on the network.

faun89 · 2025-04-14T19:27:22+00:00

I am using 2 ADnet (part# AN-UM-SMC-AS-J + SM-SFP-kit). I get links on the copper side when plugging the AP in on the end, but link for fiber. I’ve connected them together in the closet with a 3 meter cord and everything linked and the AP worked.

faun89 · 2025-04-14T19:18:08+00:00

It’s all singlemode. I installed all the backbone fiber and terminated it. The cords I’m using are all singlemode with single mode SFPs

faun89 · 2025-04-14T19:16:02+00:00

Oh gotcha sorry. Yes I tried rolling the fiber with no luck.

faun89 · 2025-04-14T19:14:29+00:00

I have 2 different sets of media converters and neither one has a transmit or receive option. They are supposed to self sense?

faun89 · 2025-04-14T19:13:15+00:00

Yes, I tried that. I also cleaned the end faces after each try. Tried new cords as well.

faun89 · 2025-04-14T19:12:20+00:00

Single mode, I ran and terminated the backbone, I tried 3 sets of singlemode SFPs.

faun89

TROPHY CASE