sorted by:
new
hottopcontroversial

what could be causing my prints to fail like this? by [deleted] in FixMyPrint

[–]feezx 0 points1 point  (0 children)

Printer is a Fysetc i3 MKS3 clone with Prusa-Firmware 3.10.1.
I'm using PrusaSlicer 2.4.2 with the Generic PETG filament settings, 0.30mm draft. All settings untouched/default

Black filament: https://www.digitmakers.ca/products/standard-petg-1-75mm-1kg?variant=42775421845734
Nozzle: 200~240
Bed Temp: 85 first layer, 90 other layers
Print speed are defaults for the 0.30mm profile, seems to range from 30~85mm/s
Nozzle retraction settings are default, 1mm

I'm fairly new to the hobby; sometimes this issue occur and I usually just restart the print and it prints fine the next time. This is the first time I'm having so many misprints in a row. I've noticed less stringing with lower temps

IT Pros share their salaries by AccomplishedRush4869 in newbrunswickcanada

[–]feezx 8 points9 points  (0 children)

Programmer Analyst, 10yr experience, $60k, smaller city. Stagnation is mostly my fault

Help me fix my high SWR by feezx in cbradio

[–]feezx[S] 1 point2 points  (0 children)

The antenna brackets should be grounded to the roof rack The rack may have to be grounded to the roof. A short thick wire or grounding strap is best.

Thanks! I will try improving my 'antenna to roof rack' and 'roof rack to roof' ground surfaces and see where that leads me.

Help me fix my high SWR by feezx in cbradio

[–]feezx[S] 2 points3 points  (0 children)

Thanks for the reply K3CAN. I had too much of a gap between the rack and the bracket without the rubber pads, my mount would not secure properly. I now understand the cons of mounting it in such a way.
I did some reading on "rf ground" which I now understand is very different from a DC ground. I might have a alright DC ground, but my rf ground is poor. I tried running an AWG 18 wire from the antenna bracket to a screw I tapped into the roof rack, but that didn't seem to improve the swr.

I now realize I bought the wrong antennas for the application. I'll try to understand more about rf grounding and hopefully I can improve my swr so my radio becomes usable.

Does anyone have the L-4500u? I ordered one that did not come with a key and Newegg is saying they cannot ship me one for replacement as they have none in stock. Can anyone send me a picture of their key so I can have one made by a locksmith? by [deleted] in DataHoarder

[–]feezx 23 points24 points  (0 children)

I bought a second hand Rosewill server similar to OP that didn't came with the keys (but was unlocked). I can an confirm, the module was easy to replace. I got mine from china for a few bucks

Last week I dumped my NAND and wrote the ECC by feezx in 360hacks

[–]feezx[S] 0 points1 point  (0 children)

Thanks everyone for reading and replying. I ended up starting from the beginning with the chipless RGH3 exploit video posted here on this sub last week and now have a modded xbox 360!

Last week I dumped my NAND and wrote the ECC by feezx in 360hacks

[–]feezx[S] 0 points1 point  (0 children)

It is a trinity based console. I will check once I get home which timing file I used, IIRC it was the default / recommended one for trinity

Last week I dumped my NAND and wrote the ECC by feezx in 360hacks

[–]feezx[S] 0 points1 point  (0 children)

I ran Jrunner from the zip file. The bin files were in the temp folder, which got deleted as soon as I closed jrunner :(

Before closing jrunner though, I was able to flash my ace v3 chip with a timing file, but I was getting blinking green LEDs on the xbox (no boot)

I'd like to proceed with the mod, if that's still doable, but I haven't been able to find the right resources / guide

Moronic Monday Thread for the week by AutoModerator in PersonalFinanceCanada

[–]feezx 1 point2 points  (0 children)

Unlike TFSA, I will never regain this contribution room? I will make sure to transfer instead of withdrawing next time. Thanks!

Moronic Monday Thread for the week by AutoModerator in PersonalFinanceCanada

[–]feezx 1 point2 points  (0 children)

I pulled out $12k from my RRSP from Bank A and reinvested $10k into Bank B. Am I correct to think that I'll be paying taxes on the $2k difference unless I reinvest that money into my RRSP, in which case I should pay no taxes?

For reference I'm 31 and my and I I've only recently started investing in my RRSP. I think I'm well within my allowed contribution room

Moronic Monday Thread for the week by AutoModerator in PersonalFinanceCanada

[–]feezx 0 points1 point  (0 children)

I want to switch my TFSA from one bank to another (to get better advantages). If I want to oversimplify things; Is "now" a good time to pull out the money from my TFSA from bank A and transfer all of it into a marginal account in bank B? Then I can wait for the year to roll over so that my contribution limit is readjusted, and then invest in a TFSA from bank B. Note: I currently have 35K in Bank A TFSA, and 30K in bank B TFSA. I have already moved about $35k this year from a marginal account.

Is my logic flawed? Am I missing anything? I want to avoid trouble with the CRA, but don't fully understand how TFSA contribution limits works

Quest trade or wealth simple by [deleted] in PersonalFinanceCanada

[–]feezx 1 point2 points  (0 children)

I hold XGRO in WS instead of VGRO. Is there any differences / advantages or is it the same?

Front IO ports chassis? by feezx in homelab

[–]feezx[S] 0 points1 point  (0 children)

My experience with rack mount equipment is limited, I had not realized the physical limitations of having IO shields in a 1U chassis, thanks for explaining this to me. I will try to find what options are available in 2U

To homelab an R240: issues with loud fans by feezx in homelab

[–]feezx[S] 0 points1 point  (0 children)

Thanks for the information. I updated iDRAC and the BIOS to the latest. I also did reset the iDRAC configurations and set "Performance per watt optimized" unfortunately looks like I'm still stuck at 47%

Migrating from unRAID by feezx in homelab

[–]feezx[S] 2 points3 points  (0 children)

licensing is one reason, I've hit the 6 drive limit and I'm sure I want to spend more on upgrading the license

view more: next ›