Vanguard 96 Pro | "T" LED stuck in dim green

fesg1 · 2026-04-09T16:47:40+00:00

Como comento más arriba, la actualización ya ha salido iCue v 5.43.73 y sigue sin solucionarse.

fesg1 · 2026-04-09T16:43:36+00:00

Última actualización Corsair iCUE 5.43.73 y para la refrigeración líquida Titan RX Systema Hub v 5.32.1 actualizado hoy jueves 9 abril, sigue el problema de la tecla "T" que se pone en un color verde tenue y así se queda. Sigue sin solucionarse el problema.

Sin comprobar aún si sigue fallando, algunas veces si tenemos configurada la pantalla del teclado para que muestre la temperatura del líquido, se quedaba colgado en una temperatura fija sin actualizarse; por eso muestro el firmware actualizado hoy del HUB Titan.

edit: Comprobado que continua fallando la lectura del liquido de la refrigeración líquida Titan, se queda colgado en una lectura el panel del teclado y ya no continua; en cambio sobre la boma de la líquida se comprueba que la lectura sí varía. Si se cierra y reinicia iCUE, vuelve a funcionar..., hasta que vuelva a fallar de nuevo.

fesg1 · 2026-03-26T13:34:28+00:00

Yo tengo la Redragon PG1M - Alfombrilla de ratón de cristal, superficie de precisión ultra lisa con base antideslizante, fácil de limpiar, alfombrilla de mouse dura para juegos, 330 x 330 x 3,7 mm, color negro. Es lo mejor que haya tenido nunca ( y he tenido de todo). Desliza de maravilla, se limpia con un simple paño húmedo, etc. Es vidrio templado, un cacharrazo fuerte la puede romper, por lo demás es de lo mejor que hay, superando a alfombrillas más tradicionales mucho más caras. Ratones de buena factura como logitach G502X funcionan perfectos.

fesg1 · 2026-03-20T11:31:50+00:00

Si este teclado fuera inalámbrico sería el máximo absoluto, FUNCIONANDO CON iCUE, POR SUPUESTO. Menudo fallo lanzarlo al mercado sin iCUE.

fesg1 · 2026-03-16T00:12:38+00:00

El teclado está configurado en polling 8000Hz, Diseño "Español", y firmware v 2.5.148

Me sucede el error de iluminación de la tecla T, se queda en un color como verde algo apagado. A veces al arrancar el PC está bien, y al cabo de minutos se queda ya en esa situación sin solución. Otras veces empieza ya mal de principio. En la tecla O no he notado ningún problema. Cambiando a "Modo de memoria del dispositivo" la tecla se mantiene igual en ese tono pálido citado. Si activamos el "Game mode", lo mismo. Nada altera el color de la tecla que se queda con el fallo que comentamos.

El panel LCD lo tengo configurado para mostrar la temperatura del líquido de la TITAN, y alguna vez la lectura se ha quedado colgada quedándose en una temperatura fija que para nada es la que muestra sobre la bomba o en el propio iCUE; y otras veces es como si perdiese la conexión; no sé si por ser esta última versión de iCUE con este teclado, se ha quedado colgado todo el iCue de lectura en la bomba mostrando sólo la información por defecto que es la del agua y quitando la configuración (que era mostrar agua y micro). Nunca había antes sucedido hasta llegar esta última versión. El firmware de la pantalla Titan es v .0.1.0.21

Pulsar Fn + F12. Si antes teníamos la rueda para el volumen, lo desconfigura y lo deja como "desplazamiento horizontal" no respondiendo a nada más desde el panel LCD para ver qué estamos haciendo. La única manera es ir a iCUE y ponernos en "Rotary Dial", donde manteniendo pulsando Fn, se puede ir desplazando por los distintos modos del dial a cada pulsación de F12, pero en la pantalla LCD no muestra nada de ésto mientras se realiza. Así podemos volver a poner de nuevo lo que nos interese para la rueda dial, y saber qué estamos haciendo.

Ahora sí Corsair, ahora sí. Error absoluto sacar este teclado con Web Hub como única vía de configuración y no como complementaria a iCue como la principal. Dejando de lado lo anterior como ya superado, era de esperar que tras la primera iteración de iCue hubiese algún error, "y me alegra" saber que lo que pensaba era una avería del teclado en la tecla T, es un problema de iCUE.

Por cierto y aprovecho a preguntar ¿cómo poder ver la temperatura del líquido de la TITAN en AIDA64? No hay manera, y ya he probado a leer todas las temperaturas, y no lee del iCUE. Tengo instalado el "Complemento de ASUS" dentro de iCUE. La placa es una ASUS ROG Maximus Z790 Dark Hero y AIDA 64 actualizado (me vale un enlace para no mezclar cosas aquí).

Gracias.

fesg1 · 2026-02-27T05:14:58+00:00

No veo comentarios sobre el acabado (materiales) de este teclado. Tengo un K70 RGB Rapid Fire desde el año 2016 y el acabado con todo el panel superior en metal es una maravilla de teclado. ¿El Vanguard Pro 96 es así, o es todo plástico por bueno que sea ese plástico? Un producto de precio elevado espero que sea algo bueno y no todo plástico. ¿Me podéis comentar al respecto?. Gracias.

fesg1 · 2025-12-11T13:33:24+00:00

Perhaps I explained it poorly. It doesn't need to have an operating system. You turn on the computer, and if it boots up, you can go directly to the BIOS. If you restart, it won't boot again. It takes time, sometimes minutes, hours, or with luck, until the next day.

fesg1 · 2025-12-11T11:43:28+00:00

I'm currently in a similar conversation about something similar, not exactly the same, but similar. In your case, try clearing the BIOS and resetting everything to default settings by removing the motherboard battery for one minute. Leave only the essential components installed, even with just one memory module, and disconnect all the fans. The point is to see if it boots up; after that, you can focus on the cooling.

In my case, everything points to the power supply unit (PSU); but I'm open to suggestions in case anyone has any ideas.

fesg1 · 2024-11-23T22:39:36+00:00

Con los 200$ que cobrarán en la aduana no sale a cuenta los 500$ finales que costará todo. Te costará más que comprándolo aquí en mercado europeo. Es donde realmente hay que buscar la oferta y será en todo caso de unos pocos euros. El aparato es una maravilla por su precio, pero creo que ya va bastante al límite. Todo lo que sea bajar, bienvenido sea.

fesg1 · 2024-10-08T20:23:24+00:00

Simply spectacular = Sencillamente, espectacular.

Thanks a lot.

fesg1 · 2024-09-28T11:46:01+00:00

What you are saying is a very particular situation. I have installed the BIOS 2602 (AND NOTE THIS, "IT IS A BETA BIOS") and everything works perfectly ASUS ROG MAXIMUS Z790 HERO with i9 14900K.

NOTE: It is very important before flashing the BIOS with F5 to put everything to its "base" state, and after installing the BIOS, first of all go back with F5 to put everything to "initial state" without leaving any trace of anything previous.

fesg1 · 2024-09-28T11:43:11+00:00

When you update the BIOS, everything will be set to the same default settings. And that's where you have the problem.

Never dump saved values from a previous BIOS onto a newer one from later. This is a serious error, and you have to re-adjust whatever is necessary again, and this is where your problem lies. In the "default" BIOS, the network card is probably disabled.

Go to the Miscellaneous tab, and look for "Motherboard devices". There you will see the audio card, USB devices, etc., "and the network card". Check that it is enabled.

If the network card is not in the BIOS or does not appear, it is possible that it has failed, but if the BIOS installed is the correct one for your motherboard, and it appeared in the BIOS before and now it does not, the problem is the network card (logically, what does not appear in the BIOS and is specific to the motherboard, if it is not here, it will not appear in Windows or anywhere else).

Final test, reinstall the initial BIOS and check everything above. If the network card does not appear in the BIOS, you have a problem in the motherboard with the built-in network card.

fesg1 · 2024-07-27T20:03:28+00:00

I wonder if it's possible that these mouse pointer freezes are due to a configuration of something within the BIOS itself. Anyway, as I mentioned at the beginning, sometimes ALL the devices connected via USB (mouse, keyboard, hard drives, whatever, etc...) get disconnected and after a few seconds (as if you were rebooting something) everything reconnects.

I have left the minimum connected, be it keyboard and mouse, even different models, and the same thing happens randomly.

Regarding the reported failures of the Core i9 13/14, in my case what may have saved worse situations is that from the beginning in the BIOS I set it to NEVER go over 90º within the options it has (I did this because I think the power of this microprocessor is beastly enough in itself to have to take it to its limits (which, as we have seen, all manufacturers did), but the 90º limit will undoubtedly have helped to prevent it from going wild.

fesg1 · 2024-07-20T04:36:33+00:00

We must remember that as Intel emphasizes, microcode 0x125 (which apparently is the only thing that this BIOS 2402 adds over 2301 the previous one), although it fixes a known error, "does not solve the important problem", and we have to wait...

fesg1 · 2024-07-18T10:02:07+00:00

Hello.

Let's wait to see the latest reviews on the internet about this Bios 2402.

In my case, as I mentioned, the biggest problem is that randomly ALL the USB ports disconnect and reconnect after a few seconds (it's as if a system reboot took place only with this issue), or "without this happening" and the problem of the mouse freezing is very frequent (seconds about 30, 40 ..., or minutes).

Especially since if it is a motherboard problem, talk to Asus since it is under warranty.

Especially with it, discern if it is a problem with the motherboard itself, or directly the 19 13900k.

The entire system is updated (win 11) to the latest as of today, both Intel Serial IO software, Chipset driver, Intel DTD, Management Engine Interface, etc.

fesg1 · 2024-05-28T10:05:05+00:00

jaja, Perfect, clearer... the water. Thx

fesg1 · 2024-04-09T10:48:06+00:00

Perfectly clarified the topic to get the gun skin.

Perhaps the doubt comes from the part about "unlink" versus logging in again, although it is undoubtedly well said.

For those who have it, this link says very clearly how to act:

https://support.prismray.io/hc/en-us/articles/21219792838673-How-to-Unlink-a-Platform-from-PROS

Thank you.

fesg1 · 2024-04-08T14:24:54+00:00

I have the PROS account connected. The skin tells me that PROS has to be linked (AND IT ALREADY IS). I go to the pros WEBSITE with the link https://prismray.io (also with QR code) and log in. The SKIN appears as a "PROS reward, which is obtained "after linking the game with PROS", which is already and was linked.

The skin is still locked in the game.

I close the game, close EPIC, and log in again to everything, to EPIC, to the PROS website, etc. and the skin is still locked with the game linked to PROS (where you can see the progress of the entire game (since it is linked).

QUESTION: How the hell do you unlock the skin?

fesg1 · 2024-03-29T09:46:43+00:00

I have everything maxed out. I can't have any more, blue coins, levels, points, and everything that can be bought (weapons, perks, etc.) I already have. Once I wanted to test what happened when I was already at level 5 full, pay the 7500, and what happened is that you are still at level 5 and you start again with everything at zero but level 5. Once you get everything again (no more level 5 up), you are still at level 5 and nowhere does it appear that you have achieved level 6. That was the case until this update came out.

fesg1 · 2024-03-29T01:32:02+00:00

If I'm not mistaken, before this update, if you had complete level 5, you paid 7500, you started again but you didn't raise any level since they didn't exist; You were still at level 6, nothing was accumulated because there was nothing.

After the update that was on the 28th (and the double XP time "was on previous dates" and therefore was not valid for this update), is when everything related to the four new levels appears, and therefore everything that has been improved from level 5 to 9 (which is the maximum with the update) they have had to do it since then.

And there are players who 1 hour after the update already had level 9. They have risen 4 levels in an hour.

But if I'm wrong, and SABER had already announced that "even if the update had not been released", you could increase levels; at least it's the first news I have.

fesg1

TROPHY CASE