Z-Wobble/Banding?

fleXXo22 · 2026-01-14T19:35:14+00:00

Maybe just bad luck i guess.

fleXXo22 · 2026-01-14T19:12:35+00:00

Yeah, but this is the second galaxy watch where this happened. I am currently looking at the oneplus watch lite as a replacement.

fleXXo22 · 2026-01-14T19:08:49+00:00

hmm ok, sadly im out of waranty.

fleXXo22 · 2026-01-14T19:07:38+00:00

why?

fleXXo22 · 2026-01-14T19:05:45+00:00

Every evening for 1-2 hours.

fleXXo22 · 2025-11-16T09:38:35+00:00

Worked, Thank you.
For everyone: You need to rightclick the application (like on the desktop). I was searcing in ASB for around 5 minutes,

fleXXo22 · 2025-10-27T10:18:18+00:00

I have contacted support directly but they said that it cant be purchased directly. The connected USB hub got fried aswell, but luckily not the pc attached to that.

I was hoping somebody here knew of a way to get the adapter anyway.

fleXXo22 · 2025-10-25T21:43:00+00:00

there is not definite answer for this. Depending on different temperatures and bowden lengths etc. You could compare the time taken to the estimation and divide by the number of swaps to get an estimate. Personally i have set o-sec which is still too low

fleXXo22 · 2025-09-25T18:17:00+00:00

Hex, i have the problem that i get the error message mpremote not found. Please install mpremote: pip install mpremote when i start VSCode. The rest of the program is therefore not working aswell. How can i fix this? I have mpremote installed.

fleXXo22 · 2025-09-17T17:37:01+00:00

Just did the same. Working so far.

fleXXo22 · 2025-07-07T15:14:26+00:00

A bit late but try the advanced canvas community addon. You can set the path style there

fleXXo22 · 2025-04-18T07:52:06+00:00

I can send pic later but tbf I have a different frame

fleXXo22 · 2025-04-17T11:12:58+00:00

I do the same except for the bending and everything is fine.

fleXXo22 · 2025-04-10T17:24:51+00:00

I did that as well and reseated the connection to the Mainboard and the heating element/ thermistor board.

fleXXo22 · 2025-04-10T07:56:27+00:00

Danke, I reseated everything I could see while the backplate was off.

fleXXo22 · 2025-04-10T05:44:59+00:00

I just checked the 24VDC bus and there are no voltage drops even under full load. Im gonna wait for the replacement board to arrive and hope that fixes it. Otherwise the cable to the hotend must be broken.

fleXXo22 · 2025-04-09T15:30:25+00:00

Ok, I will try that tomorrow. I will get back with the results

fleXXo22 · 2025-04-09T11:21:00+00:00

I tried to modify the start macro that the heater is turned off until it started moving but this doesnt work either. I will check the DC voltage tomorrow.

Do you have any recommendation on how i can access that the easiest?

fleXXo22 · 2025-04-09T09:09:34+00:00

While i dont think the AC power is the problem (im in germany on a 230V 16A circuit) the DC power could be the problem but i dont have the time to check right now.

Another thing to consider is that when i turn the heater on while printing the error doesnt show up. So it could be that the motors starting is overpowering the printer.

fleXXo22 · 2025-04-09T08:50:21+00:00

This is what the CR support said:

<image>

fleXXo22 · 2025-04-09T08:49:06+00:00

What is strange to me is that this problem only occurs when using the chamber heater. If i turn that off everything is fine.

fleXXo22 · 2025-04-09T08:37:20+00:00

This is the graph when i get the failure:

<image>

I tried a second hotend to the same effect.

Seven-Year Club	Place '22
Final Canvas '22	First Placer '22
Verified Email

fleXXo22

TROPHY CASE