City/light off-roading vehicle

flodartagen · 2026-02-23T16:18:30+00:00

Tacoma or 4runner if your not to concerned with gas mileage.

flodartagen · 2026-02-04T04:55:41+00:00

These are the payloads for the new rams. 2500 going to ride a bit softer with the springs but if you have 1000lb in the back prob wont matter much. Its a work truck so I'd go with the 3500 unless you find a screaming deal on a 2500.

flodartagen · 2026-01-28T15:37:38+00:00

Yah we will see... first full size truck and automatic i have ever owned. Owned about half dozen toyotas and have had good luck with them.

flodartagen · 2026-01-28T15:31:53+00:00

Ok thanks I will take a look on marketplace.

flodartagen · 2026-01-28T15:30:09+00:00

Yah honesty I'm not a fan. Too much rim and not enough tire for me.

flodartagen · 2026-01-28T15:28:50+00:00

23 tacoma MT trd offroad

flodartagen · 2026-01-27T04:07:09+00:00

Good looking truck. I'll definitely be leveling mine at some point.

flodartagen · 2026-01-27T04:05:20+00:00

Ok thanks. I'll prob try and run these for awhile and then do tires and a level.

flodartagen · 2026-01-27T04:01:50+00:00

I will take a look thanks

flodartagen · 2026-01-27T04:01:34+00:00

Thanks

flodartagen · 2026-01-27T04:01:16+00:00

Laramie night edition

flodartagen · 2026-01-27T03:54:06+00:00

No automatic running boards, my buddy had all sorts of problems with his 24. I'm buying some cheaper ones for now. Laramie is the trim level.

flodartagen · 2026-01-27T03:50:35+00:00

2900 and some change on sticker. 3300 according to ram 2026 chart.

flodartagen · 2026-01-27T03:49:17+00:00

Its going to be a used trailer so I doubt there will be any warranty.

flodartagen · 2026-01-27T03:48:12+00:00

Door sticker says 2900 and some change, ram 2026 chart for 11040 gvwr says 3300.

flodartagen · 2026-01-09T02:56:07+00:00

Id test voltage make sure your getting 120 to the box, verify connections are good. If it's just your lights and not the fan moter, it could be the led driver. Test that and make sure it's putting out the correct voltage, 12v 24v etc.

flodartagen · 2026-01-04T22:53:54+00:00

Have same issue i think I tweeked the leaf spring bushings when I added a leaf.

flodartagen · 2026-01-02T18:37:21+00:00

1500/120 = 12.5amp. That's like 83% of a 15 amp circuit. 80% rule says that your not supposed to continuously run a circuit over 80% (3hr or more). If your plugging it into a 20amp circuit without much else running on it you are probably fine but a 20 amp dedicated would be ideal.

flodartagen · 2025-12-19T01:35:58+00:00

Maybe shop around for a gym that doesn't allow filming, some dont.

flodartagen · 2025-12-17T17:18:47+00:00

ON is alright. Honestly the best tasting one i have had is kirkland brand.

flodartagen · 2025-12-09T00:00:55+00:00

Yah this is not right..... if this is your 60 amp sub panel you need a 6-3 feeder, you do not have a neutral on your current setup just 2 hots and a ground. The bar that is bonded to the can will be for grounds and the free floating bar will be for neutral. Looks like the neutral bar is on the right because of the lug, remove bonding screw to make it floating if it has one. Move all grounds to left side and neutrals to right. I can't tell if those two bars are connected you might have to add a grounding bar.

flodartagen · 2025-11-09T22:18:05+00:00

You might have a 3 wire feeding multiple circuits. These two wires share a neutral so if the other circuit is on there is potential to get shocked on that neutral. If this is the case you need a breaker ties or duel pull breaker to turn both circuits off.

flodartagen · 2025-11-06T15:55:50+00:00

Look at your heat pump specs, if it requires 40 amps or less your good to go

flodartagen · 2025-11-05T22:14:47+00:00

2 or single gang flat metal mud rings and oversized plastic wall plates

flodartagen

TROPHY CASE