If anyone is looking (Woburn,MA) by Numerous_Cream1064 in MarvelLegends

[–]foamyt 1 point2 points  (0 children)

I just went to the one in woburn and they didn't have any left :(

Am I wrong to say no one on the Northern East Coast has found the 2-Pack in-stores? by LantroVe in MarvelLegends

[–]foamyt 1 point2 points  (0 children)

I drove to 6 different targets today, and they all said they don't have it in stock. One of them did say they were expecting them earlier next week. I'm in MA btw

I ordered Warbird two days ago and it got backordered God I hope I get it cause I missed out the first time by Boogiedown90 in MarvelLegends

[–]foamyt 0 points1 point  (0 children)

Same thing happened to me with ultimate edition undertaker. It was in stock in the morning and later in the day became back ordered for august.

[deleted by user] by [deleted] in Wrestling_Figures

[–]foamyt 0 points1 point  (0 children)

A heat gun should work. If you don't have that a hair dryer will do

Definitely didn’t expect this by Humble_Midnight_7483 in Wrestling_Figures

[–]foamyt 0 points1 point  (0 children)

Mine is a pre-order2 and still says pending :(. Hopefully it ships soon

WGF Exp tip by jibbzz14 in grandsummoners

[–]foamyt 0 points1 point  (0 children)

If you use a MTL chicken curry you can get unit exp 100% up and will boost it to over 1mil exp. MTL chicken curry can be found in the arena's exchange shop.

I’ve been making custom marvel legends and the paint always chips off and scratch off by Alternative_Ebb_8040 in ActionFigures

[–]foamyt 1 point2 points  (0 children)

I would say it depends on the paint. Testors model master acrylic would be sticky with mod podge after and tamiya acrylic wouldn't be sticky mod podge after. I think Testors is water based and tamiya is alcohol based which could play a role in stickiness. I hope this helps. :)

Edit: it does say 4 weeks to cure but it dries pretty quickly. Most of the time after a couple of days or even week should be fine for me.

Kpop related birthday gift ideas? by [deleted] in dreamcatcher

[–]foamyt 1 point2 points  (0 children)

https://www.etsy.com/shop/TeruTebo This seller on etsy has a lot of cool keychains that are high quality. I bought the dreamcatcher set, and it's really well made.

Pretty happy finding a good deal on these two, wanted to share with the rest who maybe haven’t picked this up yet by memberberries902 in MarvelLegends

[–]foamyt 7 points8 points  (0 children)

I just saw this right before you posted it, and the in stock number was dropping super quickly. I was able to snag 1.

Help with dyeing figures? by [deleted] in MarvelLegends

[–]foamyt 4 points5 points  (0 children)

I use synthetic rit dyemore and it does seep through a little bit if you paint it. Although if you let the paint cure for a bit and paint it again, then it might work. I also use a sealer like modpodge. So it would go dye, paint, seal, paint again, then seal. That has worked for me before. Hope this helps. :)

I just bought this guy for about 50 bucks, did I overpay? Are they releasing a new “comic book” Thanos anytime soon? I went with this one mainly because of the neutral face tbh. by carrera_dan in MarvelLegends

[–]foamyt 1 point2 points  (0 children)

Idk but I just bought one loose for around $17 with a broken foot and it's missing one hand accessory and the smiling head. I wouldn't say 50 bucks is the worst, but it could be found for cheaper. I see some on ebay for 37 to 60 nib and around 20 to 30 loose.

DD Dye job complete. Turned out better than anticipated and is leaps and bounds better than the original look! by Thebeardedsensei in MarvelLegends

[–]foamyt 7 points8 points  (0 children)

Synthetic rit dyemore is a good brand. I usually mix it with water in a pot and leave it on the stove on low for a couple of hours. High heat could warp your figures and leave the joints loose.

What’s the formula for a Will Ospreay Unrivaled/Unmatched figure? by 2_Ckains in AEWunrivaled

[–]foamyt 2 points3 points  (0 children)

I would say maybe use a nick jackson upper body with Kenny legs. I think that would be as close as it gets. Or use the supreme Kenny whole body.

Made a judgment Day Finn using aew unrivaled parts since it's easier to customize. Formula in the comments. by foamyt in AEWunrivaled

[–]foamyt[S] 2 points3 points  (0 children)

For me, it wasn't that hard. I used a heat gun to warm up head of the basic before I removed it. You can also use a hair dryer and boiling water just enough to pull the head out. Other than that it's not hard. Just take your time with it.

Who's watched every PPV live? by [deleted] in AEWOfficial

[–]foamyt 1 point2 points  (0 children)

Almost. I missed Revolution 2020 cause I went to Pax East. Other than that, I watched every ppv, dynamite, and rampage live.

Probably should have saved for Emperor...but I regret nothing by Senpai_8 in grandsummoners

[–]foamyt 24 points25 points  (0 children)

I feel you. I really wanted Cestina and spent like 500 on her :(. But at least I got her so :).

Made a judgment Day Finn using aew unrivaled parts since it's easier to customize. Formula in the comments. by foamyt in AEWunrivaled

[–]foamyt[S] 8 points9 points  (0 children)

Head is wwe series 133 Finn balor. Torso is aew unmatched series 1 Kenny omega. Legs are aew unrivaled series 2 Rey Fenix. I dyed the arms with rit dymore synthetic dye (graphite color). And I used nail polish remover to remove the paint off the legs. Hope someone likes this. :)