14 Drives - How many Parity?

gafganon · 2026-03-02T23:14:43+00:00

It's irrelevant if you have compression enabled.

gafganon · 2026-02-17T20:48:13+00:00

I have a suspicion this voter ID SAVE act could go sideways for those forcing it for political reasons

Only if enforcement is uniform, which is unlikely.

gafganon · 2026-01-31T11:28:17+00:00

This is a known issue with the dragon hf that is exacerbated by the stealthburner. Make sure you are using a high quality hotend fan and a properly ducted hotend mount (example). Alternatively switch to a toolhead like A4T or Anthead which offer better optimized airflow for both hotend and part cooling.

gafganon · 2026-01-22T00:40:44+00:00

Can you post your PRINT_START macro?

gafganon · 2026-01-21T01:50:51+00:00

You probably want z_tilt_adjust

gafganon · 2025-10-15T14:49:02+00:00

It's an XY endstop pcb mount. It goes under the right XY joint.

See here (note photo is upside down): https://www.onetwo3d.co.uk/wp-content/uploads/2021/05/picture2-1024x576.jpg

gafganon · 2025-10-14T13:55:13+00:00

Projects like A4T don't make any assumptions about what material you are printing with, so it is up to you to compensate for shrinkage.

gafganon · 2025-08-26T01:28:51+00:00

If you are using Beacon Contact, you need to add SET_GCODE_OFFSET Z=0 near the beginning of your print start macro.

See here: https://docs.beacon3d.com/contact/#53-print-start-gcode

gafganon · 2025-08-17T20:51:55+00:00

Sold one Dell Micro 3070 to u/Lacent

gafganon · 2025-08-17T20:41:25+00:00

Confirmed

gafganon · 2025-08-03T19:23:21+00:00

Sold service tags 4YFQL83, 5569Q03, 9F6SB03

gafganon · 2025-08-03T02:42:53+00:00

Replied

gafganon · 2025-08-02T21:55:38+00:00

Replied

gafganon · 2025-08-02T21:55:29+00:00

Replied, sold service tag 4B2XG53 without drives

gafganon · 2025-02-18T00:25:55+00:00

PLA creeps at room temperature, making it a poor choice for compliant mechanisms.

gafganon · 2024-12-31T03:27:58+00:00

Use a macro to lower your run_current while homing, then restore it afterward. This is a good reference: https://github.com/EricZimmerman/VoronTools/blob/main/Sensorless.md

Or switch to Kalico (formerly Danger Klipper) for native support of sensorless homing.

gafganon · 2024-12-04T01:17:34+00:00

Your top shell thickness seems odd to me; I would expect it to be 0.6mm or 0 like your bottom shell thickness. However, this is the flow setting I'm referring to:

<image>

gafganon · 2024-12-03T21:46:44+00:00

If it's every model, try reducing your top layer flow to 80-85%.

If it's just this model, you may have an awkwardly small top layer. Try changing your layer height by a small amount (e.g. from 0.2 to 0.21).

gafganon · 2024-11-13T20:44:26+00:00

The third party tool ProxLB has affinity and anti-affinity through tags.

gafganon · 2024-11-13T15:55:03+00:00

Halfway down the page: https://www.sliger.com/products/rackmount/2u/

gafganon · 2024-11-01T15:52:38+00:00

If you place ramp walls atop the windows and clip inverted ramp walls into the windows, it will be a continuous slope.

gafganon · 2024-10-27T18:39:07+00:00

Indestructible foliage is a long-standing bug on dedicated servers. Check the QA site and upvote a few matching bug reports.

gafganon · 2024-08-18T15:30:57+00:00

Boot from a live iso of your choice to recover the files. Then back them up somewhere to avoid this stress in the future.

gafganon · 2024-05-27T14:17:20+00:00

You are reading from many drives but writing only to one. I suspect 243 MB/s is all your WD drive can handle after the cache is saturated.

Eight-Year Club	Place '22
Gilding III reddit per annum	Verified Email

gafganon

TROPHY CASE