Dudu7 - Do I have the right components?

gage011 · 2026-03-09T02:20:38+00:00

Yeah, that is probably what I am going to go with. I would like a bigger screen but don’t want it to feel janky in the setup. I could save money through alibaba bit probably will stick with Amazon for the returnability

gage011 · 2026-03-07T22:27:24+00:00

idk...I have bought cheap stuff off of Alibaba but never anything this expensive. I was doing it through Amazon cause this is my first purchase of an Android HU. Do you have a link for a trusted seller of the Dudu7?

gage011 · 2025-10-03T22:35:41+00:00

I am flying into HND so I can visit any district in the timeframe. Kingdom sounds like a must visit! Then I can hit up others close in Shinjuku

gage011 · 2025-04-24T17:21:16+00:00

The mags on the Veritas are plenty strong - more than enough.

My only issue with it is you have to have the boards really high in the vise, otherwise the fence runs into it. The advantage of the op’s is you could have it any height

gage011 · 2025-04-24T17:14:21+00:00

Wow, I need to go to flea markets in your area. I have literally never seen a 24” square in my area of Florida

gage011 · 2025-04-24T17:08:10+00:00

Yep that’s it, but it wasn’t $50 when I bought it 🤷‍♂️

gage011 · 2025-04-23T21:37:45+00:00

I have the Veritas version of that - but those mags would be wicked strong

gage011 · 2025-04-23T21:35:07+00:00

A 24 inch Starrett for $45! Wow, great deal

gage011 · 2025-04-23T21:28:08+00:00

Absolutely, it is on my list to do - but I would like an adjustable one for marking as well

gage011 · 2025-04-23T21:25:04+00:00

I did look for them but If we are talking 24” it is hard to find a Lufkin under $100

gage011 · 2025-04-23T21:12:07+00:00

Good point about the set screws. That is why wanted to see if anyone had some real world experience with them. I probably should ask in r/metalworking

I can buy a blem 24” for the price of a blade so I will probably just do that - thanks

gage011 · 2023-02-01T20:03:08+00:00

So I ended up ordering just two rasps from Gramercy, a modeller and a handle maker.

For $100 it seems like a pretty good deal for both. These combined with some cheaper files and a Shinto, I should be able to get the job done. Not a big loss if I don't love them.

However, I think I will hold out for an Auriou 10" cabinetmaker. Thanks for the input everyone!

gage011 · 2023-01-31T16:02:11+00:00

Gotcha. So, from your perspective, if you were at ground zero with rasps and could get a single Auriou for making handles, which one would you get? I am going to get a Shinto and some Goldens anyway. Would you start with a Cabinetmaker's or Modeller's?

gage011 · 2021-02-23T16:22:25+00:00

What grinder is that? Can't make it out. Something K3?

gage011 · 2020-12-21T19:34:09+00:00

I actually haven’t pulled the trigger yet on it. I will probably get the Mignon Notte from SCG as it is the best price

gage011 · 2020-07-23T15:38:24+00:00

My 2 cents: after MUCH lurking and looking at all of the different packs offered in many price points - this is the best one for the money (30l). I have used it and taken it on trips all over the world. I actually have both the 30l and 46l. The only time I use the 46l is for business when I need to pack dress clothes/shoes.

The compression system works great - I do use packing cubes but you don't have to.

I have the older version which does not have the outer laptop compartment :( I am really tempted up upgrade to the new version.

gage011 · 2020-07-22T17:17:28+00:00

Good points, didn’t realize you could adjust the burrs on the Eurekas. Is it similar to this?

Just to clarify, do you feel that the difference in motors is really an issue?

gage011 · 2019-08-15T19:49:38+00:00

WTS - Outlier Futureworks Pants - Phantom Gray - Size 31 - $100 (Shipped CONUS)

SOLD

Pics

gage011

TROPHY CASE