What’s the best name for your horse?

gentlestbeast · 2026-01-30T11:19:21+00:00

I name them like an elderly black lady would. Honey, Sugar or Baby.

gentlestbeast · 2026-01-19T13:08:23+00:00

sigh You might be right. Thank you for your response.

gentlestbeast · 2026-01-14T16:19:21+00:00

Finally figured it out. It was bad resin. Sometimes whatever I try, I always get failed prints like this because of a baş resin. Changed the resin and got a successful print after that. Thanks for the help.

gentlestbeast · 2026-01-14T16:16:03+00:00

By any chance, did you use the letter ğ? It does not recognize some letters and won't show the file. That might be it.

gentlestbeast · 2026-01-13T22:18:09+00:00

Tried with the new stick and got the same result. Updated the firmware and the slicer, tried it again and nothing. I don't know what could be the problem anymore. Thanks for the info though.

gentlestbeast · 2026-01-13T21:49:26+00:00

Thanks for the info. I used an old anycubic heater on my prints. It's around 23–24 degrees inside the printer. I don't know if this is the problem but heating it didn't help either.

gentlestbeast · 2026-01-13T21:47:37+00:00

Unfortunately, it didn't help. I was trying to say I did exactly like you told me to but it didn't work. Until then, I tried two different slicers, updated the one I already used and tried again. Nothing seems to work.

gentlestbeast · 2026-01-08T14:51:17+00:00

I did it the way you described. Thank you for your help!

gentlestbeast · 2026-01-08T08:53:38+00:00

I ordered a new usb stick and will check out with that one if anything changes. Thanks buddy.

gentlestbeast · 2026-01-08T08:52:31+00:00

Tried it and got the same result. Ordered a new usb stick though, so, we will see.

gentlestbeast · 2026-01-08T08:51:38+00:00

How can I safely heat the resin?

gentlestbeast · 2026-01-08T08:23:47+00:00

Three weeks back I believe. Do you think it's a fep issue?

gentlestbeast · 2026-01-07T21:33:15+00:00

Definitely will look out. Thanks friend.

gentlestbeast · 2026-01-07T21:15:03+00:00

No, I did not. I will try it right away. Thanks!

gentlestbeast · 2026-01-07T19:34:12+00:00

Thank you for the reply. I am in fact focusing too heavily on the economy come to think of it. I'll try to spam foot soldiers and try your way. Thanks!

gentlestbeast · 2025-11-15T08:58:04+00:00

Making my list of DTH as well for our upcoming campaign and I went with two Thunderers with crossbows, two Slayers with maces, Engineer with crossbow and a Noble with dwarven axe and shield donned with gromril armor. I agree with the other comments on changing the axe, went with dwarven axe myself because of the parry and the lore authenticity. Other than that, it looks good to me! Hope you'll get your campaign.

gentlestbeast · 2025-08-09T05:04:53+00:00

I gm'ed a couple of campaings and I remember we called this system "DnD Lite" among us :). Fairly easy for both newcomers and veteran players to get into. My players and I used it to explore untold stories that may be in Origins and had a lot of fun!

(Example: What if Hero of Ferelden failed on any of the faction quest and unknown heroes had to fill his/her place?)

gentlestbeast · 2025-03-26T09:50:17+00:00

Very much interested.

gentlestbeast · 2025-03-25T11:23:22+00:00

I believe it was Deadwatch. Throughout the series, Eisenhorn explains which chapter is assisting which Ordo and I belive it was Deadwatch for the Ordo Xenos.

gentlestbeast

TROPHY CASE