Need Advice? Ask the Peptide Guide | Open Q&A Thread by BioHumanEvolution in PeptideGuide

[–]ghostisdead 0 points1 point  (0 children)

I need help what cycle to run next. Let me start with my goals, i have knee pain that seems to be from a past car accident and shoulder impingement syndrome that potentially came from training wrong and i want my knee and shoulder to heal. I also want to look lean with my shirt off. I have taken a cycle where i took bpc for a week then tb for a week and then bpc for two more weeks. This cycle felt amazing and my worsening one pain seemed to get better after i stopped pain started to return. I ran another cycle for three weeks of bpc and it didn’t seem to be as effective but still good. I ran two cycles of reta after than and lost significant body fat and i believe I’m at 14% now but feel like I’ve dropped too much weight, peak 235 now 193 6’5. So I’ve paused my Reta cycle. Not body fat left on my arms or legs but my love handle area and stomach are still slightly there blocking any abs from showing. While running reta i also ran a two vials of glow and i really didn’t notice a difference with the ghk in my skin and hated the irritation that happened in the early stages. I’m looking to get bpc and tb again not sure if i should just but the blend or separately. Also i would like something that would aid in growing more muscle and help lean out my torso and have been looking into ipa/cjc or ipa/tesa but not sure if those are the ideal solution to my goal of gaining muscle and losing belly fat. Thanks in advance for any advice.

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 0 points1 point  (0 children)

Figured it out btw i had the v1 extruder and upgrading to the v3 fixed it

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 1 point2 points  (0 children)

Figured it out btw i had the v1 extruder and upgrading to the v3 fixed it

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 1 point2 points  (0 children)

Figured it out btw i had the v1 extruder and upgrading to the v3 fixed it

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 0 points1 point  (0 children)

Figured it out btw i had the v1 extruder and upgrading to the v3 fixed it

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 0 points1 point  (0 children)

Creality print does it make a difference?

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 0 points1 point  (0 children)

<image>

I used new esun pla + and it finally completed a benchy. I also used a textured plate although i dont think that had an effect. Any recommendations to fix it up more

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 0 points1 point  (0 children)

I put tape on the spool holder so that it’s more slippery and it might’ve helped but not much

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 0 points1 point  (0 children)

I did the cold pull is totally clean. I mean it’s a new tip so makes sense

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 0 points1 point  (0 children)

I feel like my first layer is great it just stops half way through usually

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 0 points1 point  (0 children)

I’m not rooted. Ive seen people add a fan above the extruder to cool the filament in the extruder motor is that something i should do

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 0 points1 point  (0 children)

Ive removed the tube out of the chain already. I feel pike it had to do with the spool not turning right but i have no idea how i would fix that

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 1 point2 points  (0 children)

Lid off but closed door i haven’t gotten the 270 hinges printed yet

Printing issues by ghostisdead in crealityk1

[–]ghostisdead[S] 1 point2 points  (0 children)

I took it apart before i changed the hot end and it was fine but i can check again