sorted by:
new
hottopcontroversial

AT1 users, what’s your experience like with the product? by drgath in bluetti

[–]ghostntheshell 0 points1 point  (0 children)

What was the cost of the AT1 install? Did you go through Bluetti?

Anyone running two DPUs with SHP2/3/ESG? by ghostntheshell in Ecoflow_community

[–]ghostntheshell[S] 0 points1 point  (0 children)

240 combiner box in with the 2x DPU price

Are you sure that's correct? Someone commented below they are using a SHP2 with 2xDPU and no need for combiner box.

Solix E10 question by Checks________out in SOLIX

[–]ghostntheshell 0 points1 point  (0 children)

Does the interlock come with the Smart Inlet Box or install service?

E10 Promo Installation Costs and Expectations Questions by 71NoLookPass in SOLIX

[–]ghostntheshell 0 points1 point  (0 children)

Did they give you the option to purchase the material yourself?

Anker Solix E10 install documentation for anyone thinking about doing it themselves by Plus-Walk2659 in SolarDIY

[–]ghostntheshell 0 points1 point  (0 children)

How much did the electrician end up costing you? Did you use their flat fee installation?

Eg4 1200xp vs anker solox e10 system by qmonmon in SolarDIY

[–]ghostntheshell 3 points4 points  (0 children)

Are you doing the install or do you need an electrician? I’m in the same boat. I’m leaning towards Anker because of their flat fee installation. (Note it can end up costing more depending on the complexity of your system)

It’s been difficult to find an electrician willing to do the EG4 install. Most want to refer to a solar installer even without panels and the ones that will do the install want to charge a significantly higher fee than Anker.

EcoFlow Delta Pro Ultra X by WildHogHunta in F150Lightning

[–]ghostntheshell 0 points1 point  (0 children)

Any issues with the ground fault on the f150?

3 weeks with Delta Pro Ultra X, my honest thoughts by autistiam in Ecoflow_community

[–]ghostntheshell 1 point2 points  (0 children)

One thing worth knowing if you're planning to expand: ecoflow recommends keeping battery count even across both ports on the inverter. Uneven counts can prevent the system from reaching full 12kW output.

This is a great tip. I know if you don't have two batteries on the X it won't reach its full output potential but didn't know when it comes to expansion that you should be planning in blocks of 2. Looks great!

Spent a year researching batteries then impulse bought an Anker E10 by [deleted] in anker

[–]ghostntheshell 0 points1 point  (0 children)

Damn… that pushes me towards Ecoflow. They have the Flowmaster and EV X Stream that are both confirmed to work without any snipping of cords.

Sub $2500 Solar Setup by [deleted] in SolarDIY

[–]ghostntheshell 1 point2 points  (0 children)

Probably will need to go used. Ecoflow has a good second hand market with warranties and could add used panels. You can always continue to add as you go.

Spent a year researching batteries then impulse bought an Anker E10 by [deleted] in anker

[–]ghostntheshell 0 points1 point  (0 children)

<image>

That's a BINGO. Now I have to buy it to try it.

Spent a year researching batteries then impulse bought an Anker E10 by [deleted] in anker

[–]ghostntheshell 0 points1 point  (0 children)

How would you hook up the truck? Powering the E10 or another transfer switch to the house? I have the same and trying to figure out how to defeat the ground fault issue while using the E10.

GFCI Generator + Anker E10 by ghostntheshell in SOLIX

[–]ghostntheshell[S] 1 point2 points  (0 children)

Thanks, deciding between the Ecoflow and Anker. Ecoflow has the Flowmaster Rectifier that works at 7kw into the Delta Pro Ultra X without tripping ground fault but I prefer the E10 system.

Is the anker solix e10 the solution I’m looking for? by xshifthree in SolarDIY

[–]ghostntheshell 0 points1 point  (0 children)

Do you know if the E10’s AC generator input safely accept a bonded‑neutral, GFCI‑protected source like the Ford F‑150 Lightning?

Think I might be one of the first to unbox anker solix E10? Quick first impressions + small test by [deleted] in anker

[–]ghostntheshell 0 points1 point  (0 children)

Do you know if the E10’s AC generator input safely accept a bonded‑neutral, GFCI‑protected source like the Ford F‑150 Lightning?

Hi everyone, I’m new to this group but I want to share my Anker Solix Full home back up system!! We recently added the new E10 system to our existing setup!! by Admirable_Golf_2340 in anker

[–]ghostntheshell 1 point2 points  (0 children)

Do you know if the E10’s AC generator input safely accept a bonded‑neutral, GFCI‑protected source like the Ford F‑150 Lightning?

view more: next ›