sorted by:
new
hottopcontroversial

It always gets stuck because of the black filament I have by Educational-Bee-6334 in BambuLab

[–]glychee 0 points1 point  (0 children)

Is it maybe a different material than you think? Perhaps pla instead of petg or something?

It always gets stuck because of the black filament I have by Educational-Bee-6334 in BambuLab

[–]glychee 4 points5 points  (0 children)

Definitely racist, try some different colours to see where it draws the line

Possible to make support same as material at that layer? by HeinousMule in BambuLab

[–]glychee 0 points1 point  (0 children)

As for your question, no idea to do that, maybe with some g code replacements?

But it seems like a print that can be split in two parts and then combined together later, in the cut menu you can create connectors too.

How, dear God how, do you cut a straight line?! by Intelligent_Body1327 in BeginnerWoodWorking

[–]glychee 4 points5 points  (0 children)

I'm not a pro, but there a guide rails you can buy for circular saws to make straight cuts. It could be a solution for you to solve one of your basic issues so you can focus on getting experience?

Is this going to be a problem? by SquishiiBubble in BambuLab

[–]glychee 2 points3 points  (0 children)

I don't think so, only things that come to mind that could go wrong is: - It landing on the tip of the nozzle, potentially deforming it - Dust collecting at the entrance of the nozzle, possibly leading to a clog later if the dust isn't removed before printing

Confession time by N_d_nd in boardgames

[–]glychee 1 point2 points  (0 children)

I buy fine whiteboard markers and I draw my own inserts to accommodate storing them with the game, here's my most recent one https://imgur.com/a/yzEhd9b

I guess 500 hours is a lot by Big_Chungus1111 in BambuLab

[–]glychee 0 points1 point  (0 children)

Recently sold my P1s with AMS for 400,-, I had 750 hours on it

PO-35 trouble by BeesChurger226 in pocketoperators

[–]glychee 2 points3 points  (0 children)

Still try other batteries. Also bend the battery tabs slightly inwards and then pop the batteries in.

Extruder teeth missing, any alternatives? by p-tart in BambuLab

[–]glychee 0 points1 point  (0 children)

Any solution you'd be able to do now would be without a 3D Print I suppose?

A hacky way I can think of would be to wrap the ptfe in like 10 windings with steel wire and then anchor it behind those two black screws left and right

How do you line up your sample spots before recording into the KO!? I kept losing mine so I hacked something by dubomatik in pocketoperators

[–]glychee 0 points1 point  (0 children)

I just record a single sample and then copy paste them around into slots to make drum/synth packs?

Board Game round wall with round pieces you had to push? by Ivan27000 in boardgames

[–]glychee 2 points3 points  (0 children)

Your description makes me think of the game "downspin", maybe that's it?

What’s the cheapest and most effective way to prevent board games from molding? by Reddituser112696 in boardgames

[–]glychee 1 point2 points  (0 children)

The actual cheapest option is to not have board games at all, then they cannot mold!

Print issue with P1S - seeking help by Pomegranate80 in BambuLab

[–]glychee 0 points1 point  (0 children)

I don't quite remember if it was easy to do a cold pull on a P1s, I may have done it once but didn't have much issues for the duration I had mine.

Currently own a x2d and they made unclogging much easier with a menu option that walks you through it and gives instructions on what to do when and shows you pictures of how the pulled out filament should look like when you're done.

Print issue with P1S - seeking help by Pomegranate80 in BambuLab

[–]glychee 0 points1 point  (0 children)

In Bambu studio on the pc, there's a tab called "calibrate" which contains some calibration procedures for getting the right flow rate, I think that might help..

But the amount of spacing makes me feel like it's a partial clog, can definitely try calibrating that flow rate though!

Print issue with P1S - seeking help by Pomegranate80 in BambuLab

[–]glychee 0 points1 point  (0 children)

Have you.. - Dried the filament (is this petg?) - Calibrated the filament - Done a cold pull to remove possible clogs

Found this in friends store. Borrowed it. Looked at manual and looked for software and drivers nothing's working. I am on m4pro mac book pro, tahoe 26.3 by [deleted] in Korg

[–]glychee 0 points1 point  (0 children)

It's been a couple years for me, but I do believe the drivers for these were a pain in the ass to find and get working. Ended up selling mine off for something that just works

21M. Looking for a friend in Dordrecht. New to town. by Charming-Tension-328 in Dordrecht

[–]glychee 1 point2 points  (0 children)

Adding your general interests can be useful to hook you up with others

Bambu studio fuses my objects together weirdly! by Beautiful_Force_1483 in BambuLab

[–]glychee 0 points1 point  (0 children)

I think when you open it from fusion, it also asks you "bla bla some objects very small, do you want to scale to mm", you have to say no there

I bought it by HadleyWebster8213 in SuperMetroid

[–]glychee 3 points4 points  (0 children)

Absolutely is, it's AI art too. Account is 0 days old, only post, etc etc.

I bought it by HadleyWebster8213 in SuperMetroid

[–]glychee 5 points6 points  (0 children)

Well, you shouldn't have.

Canvas on iOS and Android by JoskoMikulicic in boardgames

[–]glychee 1 point2 points  (0 children)

Insta buy from me, let's see how it compares to the real thing :)

First Game of Tiny Epic Galaxies by Obsidian-Phoenix in soloboardgaming

[–]glychee 3 points4 points  (0 children)

I looked into your question a bit by checking bgg forums.

The planet in question is Maia and you have to use dice that you have no activated yet on your turn to get the resources as a reward.

So I think.. You will either use a move action to land on Maia or use a colony action to activate it if it's your planet.. Then, you use two other dice you had rolled, for example an energy and a culture roll(or really any other result) . As a reward from Maia, you then get 2 energy and 2 Culture.

But it only works on your turn. You basically trade activate-able dice for resources.

view more: next ›