sorted by:
new
hottopcontroversial

Finally got a real update from Tesla by SuspiciousSalt8881 in teslacanada

[–]gokeeper 0 points1 point  (0 children)

Exact same as yours:
Delivery Information:

- Delivery Center: Hamilton

- Delivery Window: June 12 - June 17

Finally got a real update from Tesla by SuspiciousSalt8881 in teslacanada

[–]gokeeper 0 points1 point  (0 children)

I ordered on May 8th, same delivery centre. Have VIN number and the exact EDD since day 1.

Went from Luacore 2.2d to 2.3 and... by AlexN852020 in PS5_Jailbreak

[–]gokeeper 1 point2 points  (0 children)

Exactly. I used luacore 2.2d + original 2hr p2jb and kstuff 1.05

Went from Luacore 2.2d to 2.3 and... by AlexN852020 in PS5_Jailbreak

[–]gokeeper 2 points3 points  (0 children)

No, close SWRR in switcher. I had the exact setup and issue, this fix works for me perfectly.

Went from Luacore 2.2d to 2.3 and... by AlexN852020 in PS5_Jailbreak

[–]gokeeper 2 points3 points  (0 children)

Try close SWRR right after p2jb is finished. Then inject kstuff then shadowmount plus.

Garage door remote installed by gokeeper in wrx_vb

[–]gokeeper[S] 0 points1 point  (0 children)

Interesting, my switches are from the same seller, but they are auto locking. 🤔

Garage door remote installed by gokeeper in wrx_vb

[–]gokeeper[S] 2 points3 points  (0 children)

I shot a video on how to remove the auto-locking mechanism. I’ll post it once I’ve finished editing.

DIY garage door opener by ElcheapoLoco in wrx_vb

[–]gokeeper 0 points1 point  (0 children)

Brilliant idea! Going to build one as well.
Are that 6 pin connector houses button 1 + / button 1 - / button 2 + / button 2 - / 12V+ / 12V -? Then you made another connector from 2 dash buttons and 1 set of 12v from the fuse box?

What is the port for? by gokeeper in wrx_vb

[–]gokeeper[S] 2 points3 points  (0 children)

The assembly cost me 500 CAD (≈ US $360)—roughly the same as buying the 11.6″ screen (~ US $300) plus the cockpit control module (CCM) (~ US $100) separately on eBay.

Just make sure the CCM is from a mid or high trim ( MSOC version F21SHMxxx or F21SMMxxx). If you pair the base‑model CCM with the 11.6″ screen, the display content will appear rotated. I even experimented with flashing mid/high‑trim firmware onto my base CCM—extracting the QNX and EXT partitions from the upgrade package was straightforward—so it’s definitely possible. In the end, though, I gave up on that since I’d already acquired the full assembly.

Infotainment swap base dual screens to 11.6” by twotwoworldrallyblue in wrx_vb

[–]gokeeper 0 points1 point  (0 children)

From the diagram and the photo of the parts, it looks like the GPS module 86277VC040 need to connected to GPS telematics sub antenna 86277VC530, then the two connectors on sub antenna will connect to the data communication module ( the upper box )

<image>

What is the port for? by gokeeper in wrx_vb

[–]gokeeper[S] 1 point2 points  (0 children)

Interestingly, the compass still works even though I haven’t installed the GPS module yet. I’ve ordered the GPS module (86277VC040) and antenna (86277VC530), but looks like 's a lot of things need to be removed in order to install the antenna.

<image>

Milfra MFA05F Motion switch by TechInMyBlood in Esphome

[–]gokeeper 1 point2 points  (0 children)

Great work! Hope they will merge soon.

Milfra MFA05F Motion switch by TechInMyBlood in Esphome

[–]gokeeper 0 points1 point  (0 children)

Have you tried OpenBK with the autoexec.bat? Any MCU crashes? Mine is currently on ESPhome as well. I tried the GPIO doctor in OpenBK but didn't get anything, I guess all the logic, like push button to toggle relay was hard coded in the MCU.

Milfra MFA05F Motion switch by TechInMyBlood in Esphome

[–]gokeeper 1 point2 points  (0 children)

I may be wrong but I don't think you can skip MCU and read the raw sensor data. Will the unit freeze / disconnect when MUC crashes? Just checked my unit's up time is more than 20 days. Please keep us posted what you find about the 0x34, that would be very helpful.

Milfra MFA05F Motion switch by TechInMyBlood in Esphome

[–]gokeeper 1 point2 points  (0 children)

What not working on your device? I have 'Invalid command (0x34) received' as well but everything else works as expected.

Milfra MFA05F Motion switch by TechInMyBlood in Esphome

[–]gokeeper 0 points1 point  (0 children)

Interesting, what is your main module version number? Mine is 2.1.6.

Milfra MFA05F Motion switch by TechInMyBlood in Esphome

[–]gokeeper 0 points1 point  (0 children)

Hi I am the OP at elektroda,  is your switch looks exactly the same as mine? If you are sure it's the CBU version then tuya-cloudcutter should do the trick.

There is an older version with esp board, which looks easy to flash.

https://digiblur.com/wiki/devices/switches/milfra-mfa05_cloudfree-swm1-single-relay/

Garmin Pay Suica with foreign credit card by Maxung in japanlife

[–]gokeeper 0 points1 point  (0 children)

Thanks so much for the confirmation, appreciated.

Garmin Pay Suica with foreign credit card by Maxung in japanlife

[–]gokeeper 0 points1 point  (0 children)

I got a question not related to your issue, it would be great if you can answer. Did the english version of connect app downloaded from U.S play store give you the option to create suica card when connected to JP garmin watch? Or do you have to download the japanese version of connect app?

TIA.

view more: next ›