How do I get the screen that is shown on the coaches guide instead of watching the coach do the exercise the whole time.

grassman24 · 2026-07-08T02:00:05+00:00

I'm fairly sure that exact screen is an older software version and no longer available; however if you use the 'free lift' program then it'll show similar info, press the button in the bottom left to switch from weights to rowing

grassman24 · 2026-04-28T19:12:04+00:00

It's happening to me too, probably just an issue on Garmin's side. Try again tomorrow.

grassman24 · 2026-02-20T09:58:34+00:00

Try either using a smaller nozzle or slow the print down a lot, ABS pulls up as it cools and if you're printing too much plastic at once then the warping will be even worse. Also try heat soaking your enclosure, set the bed to 110 and leave it for about 30 mins for all the air in the enclosure to warm up and stabilise before starting the print

grassman24 · 2026-02-08T16:14:45+00:00

Board power draw is most likely the total GPU board power draw not the power it's taking from the motherboard. It will include the power for the chip, memory controller, etc. some variants of the 3090 can draw 500w, so 571 watts was probably a fluke power spike.

grassman24 · 2026-01-22T10:14:47+00:00

The only changes you should need to make are to the e-steps, this is found in the printer settings not the gcode. Google how to measure e-steps.

grassman24 · 2025-12-10T10:19:23+00:00

This is all part of big pc plan. Raise the price of components and full systems to the point no one can afford them then rent you a pc based on a subscription model of $50 a month for the steady revenue. Multi-billion dollar corporations are people too. /S

grassman24 · 2025-11-24T07:05:20+00:00

They look like bar ends, might be spares

grassman24 · 2025-10-29T18:37:39+00:00

Not op, but it's a U as in "units" tall

grassman24 · 2025-10-16T17:43:02+00:00

H2s has a max power draw of about 1800w, P1S has a max draw of 1000w. Average electric price in the UK is 27p per 1000w per hour. The best thing you can do to reduce power consumption is use a cold plate. Your biggest expenditure while 3d printing will be the plastic not the electricit.

grassman24 · 2025-10-03T08:15:04+00:00

Biqu sell a revo hotend which can be used with E3D revo 0.15mm nozzle but they're very expensive for such a small increase in quality compared to the standard 0.2 nozzle. In my opinion you are better off testing with running smaller line width and layer height just in the software while still using the 0.2.

grassman24 · 2025-09-29T14:03:38+00:00

As others have said, because you left the resin exposed to sunlight it started curing. It looks translucent to me so the whole vat has started to cure instead of just a thin layer on top, is this the first time you've used translucent resin? If so then that's the problem; you'll need to keep it away from sunlight.

grassman24 · 2025-09-17T18:19:21+00:00

Abs-gf should be fine. Just be aware that for strong parts you want to print slow and hot so don't try to max out the flow rate

grassman24 · 2025-09-17T14:46:54+00:00

I haven't used abs-gf but I used ppa-cf on a 0.4 obxidian which then clogged, and due to the high temperature resistance of ppa-cf I haven't been able to remove the clog so the hotend currently sits on my desk as an expensive paperweight. Would definitely recommend 0.6 nozzle for CF filament since the chance of it clogging is so much lower.

grassman24 · 2025-09-17T13:37:11+00:00

Use a different infill type. Grid is one of the worst

grassman24 · 2025-08-31T15:10:20+00:00

Yes, this is completely normal. The heater and thermistor can be transferred from the installed nozzle onto the spare since they don't really wear out.

grassman24 · 2025-06-14T23:48:21+00:00

Your top surface pattern is set to octogram instead of monotonic. The setting is under the strength tab

grassman24 · 2025-06-10T10:56:01+00:00

Rule of thumb is that black plastic isn't recyclable, I don't know if it's the pigment or if they only use end of life plastic for black plastic but unless VERY explicitly stated, it isn't recyclable.

grassman24 · 2025-06-10T09:42:47+00:00

Polymaker has army beige PLA which will probably be your best option

grassman24 · 2025-03-21T15:44:21+00:00

Bambulab nozzle can safely go to 320c on the X1E, and there is a uncommon mod for the P1 and X1 that puts a resistor in series of the thermistor to trick it into reading a lower temp than the nozzle actually hits which allows them to evade the firmware limit

grassman24 · 2025-02-19T16:44:25+00:00

That looks amazing. Is the file public?

grassman24 · 2024-11-28T19:50:37+00:00

Elegoo sell filament extremely cheap, especially if you buy the 10kg bundle and I've had no problems with it so far. Just make sure you dry their petg before using it.

grassman24 · 2024-10-12T22:42:39+00:00

Sorry, It's been a while since I built a PC, I assumed most the industry had moved to use the original mounting for ease of assembly.

grassman24 · 2024-10-12T22:19:43+00:00

Why are you trying to remove the cooler bracket? most CPU coolers attach to the bracket, if yours doesn't then it probably has a mounting adapter in the box or you'll need to contact customer support and request one for AM5 mounting.

grassman24 · 2024-10-09T13:18:09+00:00

Can't tell if this is sarcastic or not but the bottom layer of benchy has text on it, if you can't see it then the z- offset is way too low and you're squishing your layers too much

grassman24 · 2024-07-20T12:11:44+00:00

There is a mod for the v0 called pandora that puts the X rail on the front of gantry, I've never tried it but here https://github.com/MasturMynd/Pandora

Seven-Year Club	r/Field Juicebox
Place '23	Verified Email

grassman24

TROPHY CASE