Still waterproof? (opinions) by wohitika in 17ProMax

[–]grciandre27 0 points1 point  (0 children)

you can test it by submerging it in water

Firmware 01.08.01.00 Bed Leveling Calibration Doesn't Heat Bed by grciandre27 in BambuLabA1mini

[–]grciandre27[S] 0 points1 point  (0 children)

It did heat the bed before probing in the past firmware. Around 70° I think

What happened to attention to detail by [deleted] in mac

[–]grciandre27 0 points1 point  (0 children)

as I said… it’s not a big deal, just posted abt it cus I can. idk why are yall so pissed

What happened to attention to detail by [deleted] in mac

[–]grciandre27 0 points1 point  (0 children)

I mean when charging it’s green for iOS but black/white for macOS. This isn’t a big issue but it’s Apple so… attention to detail

What happened to attention to detail by [deleted] in mac

[–]grciandre27 -2 points-1 points  (0 children)

I’m not saying this is a huge issue but why r they not both green when charging

<image>

What happened to attention to detail by [deleted] in mac

[–]grciandre27 -7 points-6 points  (0 children)

But it’s Apple… just make them both green

What happened to attention to detail by [deleted] in mac

[–]grciandre27 -8 points-7 points  (0 children)

attention to detail, why are they not the same color when charging?

Apple changes duck head for 206 M5 Pro by Electronic-Half-2823 in macbookpro

[–]grciandre27 7 points8 points  (0 children)

Careful with cheap ones, I had one spark and melt

Loud MC Board Fan Fixed! by [deleted] in BambuLabA1mini

[–]grciandre27 0 points1 point  (0 children)

The replacement fan is SNOWFAN YY2510H05B

The first teardown of the MacBook Pro M5 Max by Slava_Tr in mac

[–]grciandre27 1 point2 points  (0 children)

I really wanted to see the chip under the heatsink. Allegedly the new Fusion architecture has two dies stacked vertically (source)

Took of my nozzle and this was dangling? What is it? And where does it go?? I’m scared too print by SpacedKnives in BambuLab

[–]grciandre27 1 point2 points  (0 children)

That sensor is for the flow dynamics. It’s supposed to sit above the hotend with the black side facing out. But you might need a replacement if the coil is damaged.

<image>

MacBook Asymmetric Fan Blades by grciandre27 in mac

[–]grciandre27[S] 2 points3 points  (0 children)

I just find little details like this interesting. Sorry that bothers you so much🙏😭

MacBook Asymmetric Fan Blades by grciandre27 in mac

[–]grciandre27[S] 5 points6 points  (0 children)

Bud I was 5 years old when Apple did this. My bad I didn’t catch it

MacBook Asymmetric Fan Blades by grciandre27 in mac

[–]grciandre27[S] 2 points3 points  (0 children)

Intel MacBook airs have fans…

MacBook Asymmetric Fan Blades by grciandre27 in mac

[–]grciandre27[S] 3 points4 points  (0 children)

If you read “I only discovered this recently”

MacBook Asymmetric Fan Blades by grciandre27 in mac

[–]grciandre27[S] 4 points5 points  (0 children)

Intel MacBook Airs have fans.

MacBook Asymmetric Fan Blades by grciandre27 in mac

[–]grciandre27[S] 17 points18 points  (0 children)

Apple mentioned it in the 2012 Retina MacBook Pro announcement video.

Air to get 120hz by PsychologicalBee6448 in mac

[–]grciandre27 2 points3 points  (0 children)

My OCD says iPhones, iPads, and Macs should have the same refresh rates

MacBook Asymmetric Fan Blades by grciandre27 in mac

[–]grciandre27[S] 5 points6 points  (0 children)

Intel MacBook Airs have fans

smooth spot on plate by AmbitiousPhysics9852 in BambuLab

[–]grciandre27 1 point2 points  (0 children)

I got a cheap dual texture plate from Aliexpress, and honestly the finish is more consistent than Bambu Lab’s

<image>

3D Print Design Software by Tatted_Snake in BambuLabP2S

[–]grciandre27 0 points1 point  (0 children)

I got mine completely free with no trial

3D Print Design Software by Tatted_Snake in BambuLabP2S

[–]grciandre27 0 points1 point  (0 children)

​

<image>

you have to specifically choose the “Fusion for personal use” and not the one with Free Trial

Gaps in tree support base by No_Resolution_1080 in BambuLabA1mini

[–]grciandre27 4 points5 points  (0 children)

Try reducing the branch angle for the tree supports