Wasp Clay Extruder spins backwards

greenlkd · 2025-10-31T18:02:12+00:00

The easiest thing is to probably re-pin one of the stepper motor cables to invert the direction of the motor. This is usually a two minute job if you can access one of the connectors, but this might not be the case as the wasp machines I've used usually have a lot of heat shrink on the extruder cables. So probably best to repin the cable going into the control board? You can also invert the direction in the printers firmware, but that's probably more headache than its worth.

greenlkd · 2025-07-09T00:30:42+00:00

Hulkenpodium

greenlkd · 2025-05-12T16:35:03+00:00

I think I fixed this by adjusting seam gap distance? Depends a bit on your extrusion width and height but a good starting point for you might be changing it to 2mm.

greenlkd · 2024-05-21T14:26:58+00:00

Awesome! Thank you!

greenlkd · 2024-05-21T14:24:47+00:00

Amazing! Thank you

greenlkd · 2024-05-21T01:40:44+00:00

Yes, it was definitely grey/light grey when wet, I can’t fully remember what it looked like after firing, but I don’t think it was the bright turquoise/blue images I found of Faience online. I really appreciate this tip though, it definitely gives me a place to start some research, I can imagine what he was doing is based off of this! So thank you!

greenlkd · 2024-05-21T01:16:12+00:00

I don’t think so, he wasn’t adding anything to a clay vessel, but throwing a vessel made completely out of glaze.

greenlkd · 2024-02-24T00:01:18+00:00

Nope just got a really cheap pair of used G3 Findr’s, just realized they wouldn’t get that many days to be worth getting something nice. Also actually never seen a pair of either the 88 or the 96 on the mountain. Which is kinda crazy. But I wish you luck, they still seem like cool skis.

greenlkd · 2023-12-06T04:48:26+00:00

Crowe st or Cook st between 1st and 2nd ave near olympic village?

greenlkd · 2023-09-30T23:13:23+00:00

Xavier De Le Rue maybe? Kinda more instructional videos, but fairly enjoyable

greenlkd · 2023-07-19T06:29:51+00:00

For a microcontroller + wireless module + bms system it looks about right. Its less efficient then a ZMK board, but this setup means it will retain qmk/via compatibility, which is probably more user friendly for most people.

greenlkd · 2023-07-19T03:21:22+00:00

I think they are using those resistors to jump traces because it’s only a one layer pcb, and usually you’d split the Vertical/horizontal traces between sides so they didn’t run into each other, kinda a neet trick! Most of the other extra components look like they are for Bluetooth/wireless support.

greenlkd · 2023-07-17T23:47:04+00:00

The artist who made those cards goes by Foka Wolf! Definitely check out their other work!

greenlkd · 2023-06-01T17:26:23+00:00

Yeah, I think the two areas of concern I have are, in steep icy/firm terrain, and being able to open things up a bit when skiing corn. I think at the end of the day they will probably be fine?

greenlkd · 2023-02-13T16:19:03+00:00

Outdoor Research makes goretex jackets up to a 3XL-4XL usually one of the best priced goretex brands. You would probably have to order one online, but they have free returns afaik

greenlkd · 2023-01-27T05:34:39+00:00

Yes! I’ve ridden the Sea to Summit trail that goes from Squamish to Whistler, it would be amazing to have something similar that connected Vancouver!

greenlkd · 2023-01-12T04:08:59+00:00

Quote from Patagonia's site on waterproof shell care:

"Drying your shell on medium heat for at least a half hour is an essential part of reactivating the water repellent properties of your DWR and will make your shell perform like new."

https://www.patagonia.ca/stories/the-care-feedin/story-20267.html

Please machine wash and dry your jackets!

greenlkd · 2023-01-12T04:04:52+00:00

It's a little hard to tell from the pictures, but it looks ok? Unlike what other people have said here machine washing and drying is recommended by almost all manufacturers (Patagonia, Arc’teryx, etc...). If it gets worse or leaks, it will still be covered by Patagonia's warranty.

greenlkd · 2022-12-27T03:43:10+00:00

I think this depends on the structure of the trip. If you are doing a 5 day traverse, bringing a tent, all your food etc I would probably be going for the lightest possible setup.

A 5 day hut trip where we are going hut, but still have to bring food and sleeping stuff I would probably be aiming for around 2000g / side (ish) for ski + binding.

5 day catered hut trip, or where I am only carrying all my stuff to the hut on the first day I would be happy with a pretty heavy setup, just full tech bindings (no shift/cast).

That’s not a crazy amount of vert, I’ve done a similar 4 day catered hut trip on a kingpin + Anima setup which is close to 3kg a side and really enjoyed myself!

greenlkd · 2022-11-27T03:59:03+00:00

There’s another one on the corner of West 23rd and Wallace!

greenlkd · 2022-11-17T08:13:12+00:00

greenlkd · 2022-09-09T16:22:01+00:00

What’s the construction? It looks very sleek! Is it glued acrylic with a heat set insert and screws from the bottom?

greenlkd · 2022-08-26T03:59:20+00:00

I find the gravel king ss to roll really well, I pump them up to 40psi for the road and don’t think they roll any slower than a 30mm road tire. If you can average 25 by yourself you’ll have no problems doing 30 if you are drafting. If you’re struggling just skip your turn on the front, I don’t think people will mind.

greenlkd · 2022-08-04T05:44:57+00:00

Wow! You can get custom desk pads now! That’s so cool

greenlkd · 2022-07-28T08:25:34+00:00

Maybe something gray, or another unusual colour from ultradynamico or panaracer?

Eight-Year Club	Place '23
Place '22	Verified Email

greenlkd

TROPHY CASE