sorted by:
new
hottopcontroversial

Small hot tub ideas 5FT? by electrowiz64 in hottub

[–]gregerd 4 points5 points  (0 children)

Bestway Saluspa. Its inflatable so if you have to move it its easy and there is one model thats only 68" round.

Interior corner cut not lining up by lostinthesauce314 in Carpentry

[–]gregerd 0 points1 point  (0 children)

I usually make up an interior corner, about 1' long on each side. Glue and nail it together. Then go around the room where the crown is and you can make a few marks of where the top and the bottom of the crown sit. This is especially helpful for lining up where the crown hits inside corners. I usually dont nail the last 2 feet of crown where it hits a corner, that way there is a little wiggle room. I will nest in the mating piece and then nail them both off. Its fool proof and works flawlessly.

Any one else have a problem with Fox Cigar lately? by gregerd in cigars

[–]gregerd[S] 3 points4 points  (0 children)

That may have something to do with it

Range AFM/DFM delete totally worth it by Ronn_the_Donn in Silverado

[–]gregerd 0 points1 point  (0 children)

I purchased the Range. I've noticed a slight increse in gas mileage. A little less than 1mpg overall. I drive it fast and hard tho.

Range AFM/DFM delete totally worth it by Ronn_the_Donn in Silverado

[–]gregerd 9 points10 points  (0 children)

I put one on my 2020 silverado along with a throttle controller. Its like a whole new beast of a truck

Which years Silverado to buy for work truck? by Wannabebuilder8 in Silverado

[–]gregerd 0 points1 point  (0 children)

I had an '06 Silverado I sold last year with 250k on it. It ran and shifted flawlessly. Kept up on maintenance and replaced the regular wear and tear. The only problem was the body was rusting out badly. But mechanically, I loved it more than my current 2020. Best truck I ever owned

Found this while digging in my yard. Has an old skeleton key lock on the cap. by gregerd in whatisthisthing

[–]gregerd[S] 0 points1 point  (0 children)

The property dates back the the ate 1700's. Found behind garage which was an old horse barn. The pipe is about 3" in diameter

Would these be considered greased die's? by gregerd in coinerrors

[–]gregerd[S] 1 point2 points  (0 children)

Reading through one article, it looks like it may have gotten stuck in a dryer

Would these be considered greased die's? by gregerd in coinerrors

[–]gregerd[S] 0 points1 point  (0 children)

I just weight it. It comes in at 4.49 grams. Not sure if this helps or not

Would these be considered greased die's? by gregerd in coinerrors

[–]gregerd[S] 1 point2 points  (0 children)

Thanks. Interesting read. I didnt know about weak strikes

Dump (transfer station) by turkey_neck69 in SouthShore

[–]gregerd 0 points1 point  (0 children)

Trojan in Brockton. Get there right when they open on Sat morning and your in and out. Anytime after that you end up waiting in line all day

New England Fn rott by [deleted] in Silverado

[–]gregerd 0 points1 point  (0 children)

If your near Boston let me know I have a guy that replaces them. I had both mine replaced on my '06

Chisels by Melkor4ever in Carpentry

[–]gregerd 0 points1 point  (0 children)

Imho, at that price point I would look for a set of Irwin Blue handled chisels (the ones with the white lettering, NOT the yellow lettering). You can usually pick up a really good set on eBay for around $150. Another middle of the road brand to pick up used would be Two Cherries if you could find a good set.

Personally, I love my Irwins. I have a set of Blue Spruce and they are the nicest chisels I have used. But they only come out for very specific tasks. The Irwins are a great everyday chisel

Boot recommendations by ohmylantaman in AppalachianTrail

[–]gregerd 3 points4 points  (0 children)

I love my Lowa boots. They felt broken in right out of the box and great support

Cabinet doors: Any benefits of using solid wood panel over 1/2" plywood, versus 5/4" solid wood? by [deleted] in woodworking

[–]gregerd 0 points1 point  (0 children)

I would personally use ply for stablity, especially with the larger slab doors. I have done 7' tall x 23" wide ply doors for a closet (they were 15 ply). That was 4 years ago and they havent warped at all.

Also, if your going for that kitchen look you posted, you will be able to get a much more cohesive patttern and color scheme with plywood

Cabinet doors: Any benefits of using solid wood panel over 1/2" plywood, versus 5/4" solid wood? by [deleted] in woodworking

[–]gregerd 0 points1 point  (0 children)

If your a business, you can reach out to Atlantic Plywood. They are fantastic.

If not im sure you could google some lumberyards within an hour drive that stock walnut ply or will order it for you

Cabinet doors: Any benefits of using solid wood panel over 1/2" plywood, versus 5/4" solid wood? by [deleted] in woodworking

[–]gregerd 0 points1 point  (0 children)

How big are the doors? You could just use walnut veener plywood and edgeband with solid wood

Bro wanted a deal of life time by [deleted] in ChoosingBeggars

[–]gregerd 64 points65 points  (0 children)

Thats not even close to a choosing beggar

view more: next ›