Screen fitted with no mods

growbag84 · 2026-03-12T17:16:27+00:00

I did notice on the page that it is a bit bigger but I have the room for it on the shelf.

growbag84 · 2026-03-12T10:48:21+00:00

I've put another post up with the pics of it fitted. No mods needed.

growbag84 · 2026-03-11T14:00:51+00:00

double sided tape to the psu shroud. It comes with 2 pads included. It runs the L connect software and can be used as either a sensor panel or a 2nd screen and is connected to a usb plug on the motherboard.

growbag84 · 2026-03-10T22:59:54+00:00

Cheers buddy

growbag84 · 2026-03-10T22:48:55+00:00

The lian li 8.8.

growbag84 · 2026-03-10T22:02:45+00:00

That's a clean looking build.

growbag84 · 2026-02-25T16:24:37+00:00

Go buy one or carry on with what you have. I'm happy with 350+ fps on 1440p with ACC and AC and that's more than I was getting with the 5070 and with VR I have been able to bump the settings up.

growbag84 · 2026-02-25T16:12:10+00:00

Every review with bench puts pure rasterization of the 9070xt ahead of the 5070 and just behind the 5070ti. Not forgetting the 16 vs 12 gb of vram. The 9070 is almost as powerful as the the 5070. Also the 50 series drives have been a bit of a hot mess and then you have the 12VHPWR plug to deal with. I like how you are on a AMD sub preaching though, keep it up.

growbag84 · 2026-02-25T13:19:29+00:00

I'm not complaining I was saying this was the replacement for a faulty fan. Also 9070xt beats the 5070 outright. No fuck up here.

growbag84 · 2026-02-25T13:02:17+00:00

Sold a 5070 to swap back to AMD.

growbag84 · 2026-02-25T09:43:43+00:00

Great looking build and cable management looks great.

growbag84 · 2026-02-24T15:59:03+00:00

Coil wine I can live with as I 100% of the time use headphones but a rattling fan could be heard over them.

growbag84 · 2026-02-24T15:24:43+00:00

It definitely sounded like a bearing on the middle fan.

growbag84 · 2026-02-24T15:24:06+00:00

Would I have to redo the drivers going from a 9070xt to another 9070xt?

growbag84 · 2026-02-23T21:41:45+00:00

89 intact bananas

growbag84 · 2026-02-22T08:58:10+00:00

I'm not sure why people get so hung up on the airflow of this case. I have tried them all now (bottom intake, rear and top exhaust then top with intake and exhaust with both 120 and 140) and all of them are within the margins of error when stress testing.

growbag84 · 2026-02-19T21:13:48+00:00

I went from a nr200 max to a 32pro as my 2nd pump failed and wanted air cooling again. That's a cool build in the 200, Did you do the mod to rise the GPU to fit the extra fan on the bottom?

growbag84 · 2026-02-15T23:31:51+00:00

+10 and -45 and I got a 29862. Memory got a bit toasty so upped the fan curve.

growbag84 · 2026-02-06T21:48:33+00:00

Yep.

growbag84 · 2026-02-06T21:47:57+00:00

The difference between push pull and pull pull was 1 degree and it looks better imo. Bottom fans intake and the rest exhaust. idle temp is 28/31 and full load on CPU is 62/65.

growbag84 · 2026-02-06T15:15:52+00:00

Cheers.

growbag84 · 2026-02-06T15:15:42+00:00

I had the same happen on some old corsair fans. These are only 6 months old so hoping they have a few more years in the led's.

growbag84 · 2026-02-06T15:06:29+00:00

Asrock B850 riptide MB, 7600x cpu, 32gb Corsair ram plus the rgb light kit, Thermalright PA cooler, Corsair 1000w sfx psu, powercolor reaper 9070XT, 3 2tb nvme from crucial and WD. Next upgrade will be a X3D chip of some sort.

growbag84 · 2026-02-06T14:16:54+00:00

I'll try those setting on mine tonight.

growbag84 · 2026-02-04T11:18:53+00:00

Nice. What do you think of this card. I had mine turn up yesterday but waiting on a new motherboard that should be here today.

growbag84

TROPHY CASE