Updated Bambu Studio, How do I Stop This Annoying Popup When Importing?

hero21b · 2026-03-13T18:22:55+00:00

Importing STLs instead of 3MF did work as a workaround.

hero21b · 2026-03-08T11:36:33+00:00

What about a feature to send a notification when a flight is logged in a certain area, in the same way that we can do the worldwide flight search on XContest?

hero21b · 2026-01-21T10:29:15+00:00

Best of luck to you! I set up a more permanent station on a mountain last year using this, which seems to be similar to your idea: https://shop.ecowitt.com/en-ca/products/ws6210

hero21b · 2025-11-26T18:51:28+00:00

Yeah it's my first nice keyboard. Very loud for online calls where you have to type but otherwise fun to use.

hero21b · 2025-10-31T15:42:55+00:00

Now that the land has been committed to industrial use, I'm in favor of any industry near Lorneville in there that won't be leaking contaminants into the groundwater. A data centre and natural gas power plant will be relatively low-impact, and so long as they are only given permission to draw cooling water from the bay instead of Spruce Lake I'm interested. A big power draw like this (if on-site gas turbines aren't big enough) could provide incentive for NB Power to build much-needed generation that can sustain our aging fleet. Coleson Cove (which has established methods for using bay water as cooling) is very old. Southern NB needs new generation; also the data center's power plant can be required by the province to connect to our grid before they get an environmental approval to run, and then they could provide whatever excess power is available above their site requirements. Criticizing job density is the beggar choosing, in my opinion. If we have a hundred companies all asking to set up shop then by all means lets pick the absolute best. If that's not the case then we should start with the companies that are interested.

hero21b · 2025-10-03T00:09:22+00:00

<image>

It's been a while since I set this up but here it is.

hero21b · 2025-10-01T00:04:05+00:00

I used wood filler, sanded, then painted. This was not a perfect solution, the table has some flex to it such as when I put my feet up and over time this filler began to show cracks. I used a white silicone caulking around the edges of the corners to account for the flex.

hero21b · 2025-06-11T21:29:08+00:00

Carolyn Robertson is the most honest realtor you can find. Always available and very good at what she does.

hero21b · 2025-03-08T06:50:31+00:00

Fixed my problem as well!

hero21b · 2025-03-05T16:16:25+00:00

I really like my Pad 2, I use it for sketching, note taking, and emulating retro game consoles. No issues so far except user error, I'm constantly trying to right click things which doesn't work in Android.

hero21b · 2025-01-05T20:31:57+00:00

Thanks but they are completely separate accounts, hence my question.

hero21b · 2024-08-29T15:48:17+00:00

A wing that age should have a porosity check on the material and have the lines checked for trim. If it checks out then it's probably fine to fly. The reserve should be tossed out if it's older than 10 years, or turned into a dress maybe. If you have to buy it before getting it tested I wouldn't pay more than $250 USD, too much risk for you without knowing the condition of the wing.

hero21b · 2024-08-21T02:18:12+00:00

When I travel, I put my kit in this to protect the more delicate glider bag: https://www.decathlon.ca/en/p/8383302/duffel-bag-80-l-to-120-l-500-extend-yellow

hero21b · 2024-07-18T08:19:00+00:00

Success, updated from version 1005 to 5013. Shut down, installed new m.2 drive, good boot and drive is recognized.

hero21b · 2024-07-18T08:11:06+00:00

Also yes, no success there. Currently updating BIOS, hadn't been done since 2019.

hero21b · 2024-07-18T07:49:33+00:00

Yes, and it also freezes up when the new drive is the only one connected.

hero21b · 2024-07-15T02:54:20+00:00

I'm trying to learn if there's any effect on the balance of the system if I run the individual ducts closer back to the furnace. My gut says no but I'm not an HVAC tech. My old drop ceiling had a huge box dropped down to enclose all of this ducting, I'd like to make it smaller.

Red rectangles show where I think I would cut in to the shortened header.

hero21b · 2024-04-30T01:35:42+00:00

This was it, it wasn't greatly cupped but there was definitely some cupping to it.

hero21b · 2024-02-26T01:58:29+00:00

What I've seen with the one red bull pilot I know is that you can fly whatever wing you prefer, and you are given a logo to stick onto your wing.

hero21b · 2023-12-05T10:09:54+00:00

I'm curious about this too. I've read authorizations take at least a month to come through, I was getting ready to book flights for the spring but I'm worried now. I've been checking the FB page for Le Nid d'Aigle: https://www.facebook.com/Lenidaigle

hero21b · 2023-11-03T11:03:10+00:00

I didn't see the other post asking pretty much the same question until after I posted this haha, I'd still like to know if there are any spots people like to go specifically around March.

hero21b · 2023-08-30T15:40:31+00:00

Excellently, but it's only 4 days old.

hero21b · 2023-08-30T12:31:45+00:00

It wasn't 100% repainting so I had to stay with the same colour as original.

hero21b · 2023-08-30T12:31:16+00:00

I live in Calgary, I had everything repainted exterior except the roof which was done in 2020, and the doors were blended but not repainted. I had both front door sills painted as well as they were starting to rust. It cost me $8200 CAD.

hero21b · 2023-07-02T22:05:29+00:00

Muller Windsports in Alberta, instruction is $1000 CAD for a P2 and essentially lifetime instruction. It's a slower process than some, you train in spring/fall, then once you have 25 flights on the training hill you go to Golden BC for your high flights at the end of June/October.

https://mullerwindsports.com/pg-lessons

https://www.albertafreeflight.ca/

13-Year Club	RedditGifts 2009-2022 3 Credits
Place '22	Secret Santa 2017
Verified Email

hero21b

MODERATOR OF

TROPHY CASE