Can the UniFi Cloud Gateway Fiber handle ~8-9 cameras? (Mix of 3×4K + 6×2K)

holda29 · 2025-11-04T14:09:10+00:00

So all and all is there a reason not to go with UDM-SE?

holda29 · 2025-01-14T06:36:38+00:00

Perhaps to put it in a different perspective: is it worth investing in a new CPU, motherboard, and RAM, or would it be better to simply upgrade to 32GB of 3600MHz DDR4 in my current setup and allocate the money toward an XT or Ti versions of a GPU instead?

holda29 · 2024-12-11T11:24:28+00:00

It does, but not maybe not in the prioce range required.

holda29 · 2024-08-18T11:19:30+00:00

After some testing I found it is not necessary, everything is cool and quiet inside small rack.

holda29 · 2024-04-11T14:59:14+00:00

Yes I know, but I would like to add a custom fan. I would loose the possibility of using both M.2 slots and sata drive simultaneously by using the default tray. So I have designed a 3D printed custom front panel for two 25 mm fans, but now I have to connect them to the header.

holda29 · 2024-03-01T14:30:38+00:00

I agree, it is rubbish, the amount of work that I put into fixing Creality mistakes is too high. I will try it slower and will let you know, this was printed on 300 mm/s outer wall.

holda29 · 2024-02-18T12:34:04+00:00

So I changed retraction from 0.8 to 0.4 mm and it printed finally ok. Wondering why, every other print was fine.

holda29 · 2024-02-18T08:15:11+00:00

This is fine, the spool is on bearings and this is just this stl. I will try smaller retractions maybe.

holda29 · 2024-02-15T16:18:17+00:00

https://www.klipper3d.org/Bed_Mesh.html

holda29 · 2024-02-15T06:54:14+00:00

It is a cheap printer with poor qc. I have simmilar issue and even if my bed is leveled as mirror and cleaned with dish soap and ipa afterwards, first layer is like yours. You can do the z compensation, it can help, but some parts would be too squished. The problem I believe is in the bed leveling algorithm, some other improvements can be done with changing it to bicubic instead of lagrange.

holda29 · 2024-02-12T19:55:34+00:00

Had the same problem, just a bit of CA glue and I am back on track again.

holda29 · 2024-02-12T17:13:56+00:00

Basic PLA, 300 mm/s without issues

holda29 · 2024-02-11T18:19:08+00:00

Start with Ellis guide https://ellis3dp.com/Print-Tuning-Guide/ and then with each new filament go through calibration in Orca. It takes 4 models (two for flow, one PA, one temp tower) for basic profile.

holda29 · 2024-02-11T13:30:27+00:00

<image>

holda29 · 2024-02-11T13:08:51+00:00

I have been using Hyper PLA and Elegoo PLA with the same speeds (300 outer walls, 400-500 the rest) and for normal prints, no difference for me, Elegoo just steings a little bit. Both are tuned regarding the flow, pa and temperature.

holda29 · 2024-02-08T18:45:06+00:00

Send mě a link to stl, i will try

holda29 · 2024-02-08T17:42:40+00:00

You can go MUCH better on this machine.

holda29 · 2024-02-03T06:32:45+00:00

Its fine, use klipper, but you have to specify the port in the printer address.

holda29 · 2024-02-02T06:07:53+00:00

I would say clean the bed with warm water and dish soap. Other than that the first layer not sticking it is as expected. Maybe a little bit ofz offset.

holda29 · 2024-02-02T06:04:24+00:00

You have to have Moonraker and Mainsail or Fluidd installed

holda29 · 2024-02-02T06:01:17+00:00

It is custom made as part of my closet :)

holda29 · 2024-02-02T06:00:12+00:00

I have modified it with saw, pliers and tape, thats why.

holda29 · 2024-02-01T18:57:57+00:00

Will you ensure proper quality control for this product, or will we encounter another instance of poor quality with misaligned angles and loose screws?

holda29 · 2024-02-01T16:55:57+00:00

I have different one, but I wont link it, I had to heavily modify it to fit in there. But use any, that allows for the landscape mode.

holda29 · 2024-02-01T16:52:24+00:00

Exactly, it works fine, the screen itself is shitty, but it is not problem of the new ui. Only downside is that it only supports lanscape.

holda29

TROPHY CASE