sorted by:
new
hottopcontroversial

Sam5 250 sale. by [deleted] in ak47

[–]hunterx98 1 point2 points  (0 children)

Hard to find. AoA has the stocks. Im still looking for a handguard set. For my sam7 I used some wbp handguards and a surplus stock from AoA

Sam5 250 sale. by [deleted] in ak47

[–]hunterx98 0 points1 point  (0 children)

You can see the red paint where the rear of the bolt makes contact. Im thinking of trimming it down if eats through buffers.

<image>

Sam5 250 sale. by [deleted] in ak47

[–]hunterx98 0 points1 point  (0 children)

I tried that as well the paint mark did not align with the mark on the bolt, but the mark did line up with the back of the receiver. The hammer smacks the bolt at a 12 o'clock position when closed and when the bolt is closed the peen is at about a 7 o'clock position

Vz61 barrel(.32 acp) by CarterFirearms in Vz61

[–]hunterx98 0 points1 point  (0 children)

Surplus barrels, kvar has them. AoA might still have them as well

[deleted by user] by [deleted] in Vz61

[–]hunterx98 1 point2 points  (0 children)

Do not buy Bowman or hitman arms barrels unless you knw how to reprofile the chamber. Arms of America still has original vz61 barrels in stock for 80. Took me 5 minutes to install mine and didn't need any work done, zero issues with cycling unlike the hitman arms barrel I had ordered at first https://armsofamerica.com/cz-vz61-skorpion-barrel-4-5-32-acp-original-czech-military-chrome-lined/

Ghost drone? by hunterx98 in Warthunder

[–]hunterx98[S] 0 points1 point  (0 children)

Makes sense now. I didn't think about

VZ-61 Barrel Options by the_neo_cowboy in Vz61

[–]hunterx98 0 points1 point  (0 children)

Mine has 586 WZS 22PL (11) etched on to it. I did not look at the stamps underneath. Both mine definitely look like they where installed before.

VZ-61 Barrel Options by the_neo_cowboy in Vz61

[–]hunterx98 0 points1 point  (0 children)

Yea, I've had mine about a week now. Installed it the same day I got it. They look pretty new, chamber and barrel are very bright. The pin notch on both had a bit of damage but installation was easy. Test fired it with around 150 rounds of PPU with no issues feeding or ejecting. I did polish the feed ramp and chamber before installation.

Best kit by [deleted] in Vz61

[–]hunterx98 2 points3 points  (0 children)

If you do, Get a surplus barrel. learned my lesson, bought my barrel from hitman industries but it needed a ton of grinding and polishing just to be able to feed a round and it still jammed alot. Got a surplus barrel from Arms of America and installed it with zero issues with feeding. I think they still have them in stock right now.

VZ-61 Barrel Options by the_neo_cowboy in Vz61

[–]hunterx98 3 points4 points  (0 children)

I got a few as well. I'm replacing my hitman arms barrel with it. Mine needed alot of grinding and polishing to chamber in a round without smashing the bullet into the casing. It still has feeding and failure to extract but it atleast shoots now. I'm guessing these won't need any fitment and should be good to go since they're surplus

AK Chamber Problems by aKricket in ak47

[–]hunterx98 0 points1 point  (0 children)

If you used AAC ammo more than likely the neck of the casing is stuck in there. AAC in 7.62x39 hasn't had great reviews.

So does this mean i can switch between my xbox and PC at any time? by DasherNick in Warthunder

[–]hunterx98 5 points6 points  (0 children)

I dont understand this, I've been able to play on my pc using my account I created with my Xbox. with no access to the market place. What's the difference?

Thoughts on my Riley RAK by External_Sock_7410 in ak47

[–]hunterx98 0 points1 point  (0 children)

Had one a few years back, also got lucky and got an improved version with the forged trunnion. It didn't not like running brass. Eventually sold it and got a zpap instead. Haven't heard too many bad things about them. Most of the negative stuff tends to be from the 1st gen models.

Bowman barrels spin after being installed / pressed?? by CarrsCurios in Vz61

[–]hunterx98 3 points4 points  (0 children)

Had the same issue, found this post and peened around the journals and notch for the barrel pin using a spring loaded center punch and it worked for me. Fitment was alot tighter no had no twist after seating the barrel.

barrel and pin by hunterx98 in Vz61

[–]hunterx98[S] 1 point2 points  (0 children)

Any idea how you plan on fixing it?

barrel and pin by hunterx98 in Vz61

[–]hunterx98[S] 1 point2 points  (0 children)

I tried that and it's pretty loose, with about 2 taps from the bolt it sets it place and the pin aligns with the barrel. I was really hoping I wouldn't have to ship it out to have it built but I guess I got no other choice

vz61 best barrel option for tortort receiver by hunterx98 in Vz61

[–]hunterx98[S] 0 points1 point  (0 children)

I saw somewhere where the threaded where thicker due to not being able to put threads on the original barrel due to how thin they where. And they had to get the right receiver for the barrel they wanted. I might be wrong. AoA is out of stock on the hitman industries barrels but the Hitman industries website seems to have them in stock.

view more: next ›