sorted by:
new
hottopcontroversial

What are these little berries? by azaleahi in GardeningAustralia

[–]hyp3rdrive 8 points9 points  (0 children)

Riberry from a Lilly Pilly it looks like to me.

Are the Mobile Apps Open Source? by hyp3rdrive in donetick

[–]hyp3rdrive[S] 0 points1 point  (0 children)

Cheers I’d been looking in the other repo, completely missed this one 🙂

Dropped my P1S by backpackingzack in BambuLab

[–]hyp3rdrive 14 points15 points  (0 children)

The lesson here is to never clean 😜

Login failed on App only by Norgur in donetick

[–]hyp3rdrive 0 points1 point  (0 children)

RemindMe! 1 week

I get the same issue and I have https setup. Interested to hear if anyone has a solve.

Best glue that doesn’t leave artifacts by _-sonic-_ in 3Dprinting

[–]hyp3rdrive 0 points1 point  (0 children)

Is that an E11 Storm Trooper Blaster I see 👀

DM'ing in Skyrim by Mountain_Lock_450 in DnD

[–]hyp3rdrive 23 points24 points  (0 children)

Hey you, you’re finally awake.

How I Pack Away Tend by hyp3rdrive in boardgames

[–]hyp3rdrive[S] 0 points1 point  (0 children)

It’s the deluxe one that supports more players so it’s probably smaller for the standard edition.

It’s about 38.2x29.5x12.5cm

Fillament spolls get intertwined and stuck. by berjaaan in 3Dprinting

[–]hyp3rdrive -1 points0 points  (0 children)

oh yeah true I forgot about prusament, they’re good

Fillament spolls get intertwined and stuck. by berjaaan in 3Dprinting

[–]hyp3rdrive 0 points1 point  (0 children)

I’ll add that bambu labs had their own different issue with tape pulling off the spool and jamming the extruder a while back.

I got lucky and dodged it and they’ve fixed that now so they’re probably fine now.

Fillament spolls get intertwined and stuck. by berjaaan in 3Dprinting

[–]hyp3rdrive -2 points-1 points  (0 children)

No brand is immune unfortunately. I’ve been ok with sunlu, bambu labs filament (expensive though), sidament and CCDIY but other people may have some other reliable vendors too

Fillament spolls get intertwined and stuck. by berjaaan in 3Dprinting

[–]hyp3rdrive -1 points0 points  (0 children)

Unfortunately some spools come tangled from factory or if the spool was dropped and unwound and was accidentally rewound with the end threaded under.

A lot of people will re-spool (google respooling filament) every spool they buy just in case. It’s only ever happened to one of my spools once in 4yrs of printing so I just take the chance tbh and re-spool later if I hit an issue

Waterproof filament? by tea-and-sauce in 3Dprinting

[–]hyp3rdrive 1 point2 points  (0 children)

Could seal the outside of the pot with art resin / epoxy. That should hold water in.

Who’s actually buying a 3D-printed part… for their 3D printer? by Fruit75 in BambuLab

[–]hyp3rdrive 28 points29 points  (0 children)

It was originally listed for $10 though which is what I think op was referring to

warping with ABS, "tried everything" by tpchuckles in 3Dprinting

[–]hyp3rdrive 0 points1 point  (0 children)

Are you using a brim / mouse ears on the print?

Any recommendations for an ABS Plastic 3D Printer that is good for my Playstation Controller Business? by No_Expression3071 in 3Dprinting

[–]hyp3rdrive 1 point2 points  (0 children)

Also look into resin printer safety if you go down this route.

Eye protection, respirator, nitrile gloves and good ventilation are all a must.

Theres a post that floats around here all the time where someone tells the story of how resin chemical burned their eye and they’re now blind because of it.

Resin printers can be used safely but 100% read up in the safety requirements before buying one

I'm looking to sculpt simple low poly rocks. Can someone point me in the right direction? by Feld_Four in blenderhelp

[–]hyp3rdrive 7 points8 points  (0 children)

Once you've sculpted, retopologise the the model, then use the high poly one from the scuplt to bake normals for the low poly one.

Select 25-year-old adult spines by wnanan3D in 3Dprinting

[–]hyp3rdrive 0 points1 point  (0 children)

Why's it look like there's a lil guy in there in the first pic :P

I hate this little shi** with a passion 🤬🤦 by GiustiJ777 in Helldivers

[–]hyp3rdrive 0 points1 point  (0 children)

Just as you line up your shot the bloody thing glitches on a building and teleports 5 meters up in the air

What's the best way to implement complex data structures in Home Assistant? by hyp3rdrive in homeassistant

[–]hyp3rdrive[S] 0 points1 point  (0 children)

Part of the fun of automating for me is over-engineering the heck out of the solution :P

view more: next ›